9-199-26風機樣本解讀_第1頁
9-199-26風機樣本解讀_第2頁
9-199-26風機樣本解讀_第3頁
9-199-26風機樣本解讀_第4頁
9-199-26風機樣本解讀_第5頁
已閱讀5頁,還剩18頁未讀, 繼續免費閱讀

下載本文檔

版權說明:本文檔由用戶提供并上傳,收益歸屬內容提供方,若內容存在侵權,請進行舉報或認領

文檔簡介

1、丹徒糧機9-19、 9-26 型離心通風機、 用 途1.1 9-19、9-26型離心通風機,一般用于鍛冶爐及高壓強制通風,并可廣泛用于輸送物料、輸送空氣及無腐蝕性不自燃、不含粘性物質之氣體。介質溫度一般不超過50C (最高不超過80C),介質中所含塵土及硬質顆粒不大于 150mg/n?。二、規格與結構特征2.1風機葉輪直徑的分米數即為風機的機號,用阿拉伯?dāng)?shù)字表示。機號后的字母表示 風機的傳動方式,傳動方式常用的有:“ A”式表示與電動機直聯傳動(葉輪裝在電機軸上)?!?C'式一一表示通風機懸臂,皮帶輪在軸承外側傳動。“ D'式一一表示通風機懸臂,有支撐、聯軸節傳動。2.2風機的

2、旋向分為左、右旋二種,其區分方法是,從傳動方向正視葉輪,風機工作 時葉輪順時針旋轉的為右旋,反之則為左旋。2.3風機的出氣口方向一般均制成 90度,如用戶有特殊要求,可在定單上注明(風 機的各種出口角度見圖1)。以下視圖均從電機一端正視2帀邛圖i為便于客戶安裝、調試,同時供應鋼結構的整體支架及減振支架。2.4風機主要由葉輪、機殼、進風圈、軸承座等部件組成。其中葉輪由曲線型輪蓋、葉片、直板輪盤組成,并經靜、動平衡校正。軸承座采用滾動軸承用鈣基脂潤滑。三、風機的性能3.1風機的性能參數可見性能表3.2在性能表各工況點,所需電機功率:K(kw)102*” mP*Q式中:Q 流量(M/h)N 電機功率

3、(kw)P 全壓(mmH)n 全壓效率n m-機械效率“ A”式為1, “C'式為0.96K 電機容量安全系數,2-5kw取K=1.2,大于5kw,取K=1.153.3、所附性能參數表是在一定轉速下,標準狀態下風機性能參數,如通風機的轉速、 葉輪直徑或氣體密度發生變化,則性能參數換算公式如下:滋.公 目 算 換 項DbM D2mnz nmP# PmD2=D2m n=nmP式PmD2=D2mn工nmP = PmD2工 D2m n=nmP = P m壓力換算P P < D2 f pm Pm(D 2 m JQ20丿ppPm PmPf n 2Pm(nm 丿P=Pm(D2、I D2m 丿2

4、流量換算Q ( D2 Qm D 2 m 丿n nmQ =QmQ nQm nmQD八Qm I D 2m 丿3功率換算NmPm(D2m 丿 Jm 丿NPNmPm理a3Nm >nm 丿£Nm5效率nm四、安裝、調試和運轉3.1安裝前應對風機各部件進行全面的檢查,葉輪與機殼的旋轉方向是否一致,各部聯接是否牢固,葉輪轉動后有無碰擦,如發現問題應立即給予調整。3.2安裝時注意檢查機殼內不得遺留工具和雜物,進出風管道聯接時應自然吻合,不得強行聯接,絕對不允許將管道的重量加在風機上,并注意風機主軸的水平。3.3對聯軸器或帶傳動的風機,要檢查聯軸器或帶輪、皮帶是否安裝可靠。兩帶輪位 置是否在一條

5、中心線上,風機軸與電機軸的同心度是否符合技術要求(徑向位移0.1mm 傾斜度 0.8/1000 )。3.4風機安裝完畢,可進行試運轉,在風機啟動時必須在無載荷即將進風調節門關閉出風調節稍開的情況下進行(特別是鍋爐引風機或高溫通風機),在啟動過程中應嚴密注視電流,不得超過電流額定值,如情況良好,逐步將閘門開啟到工況點 為止。3.5當風機啟動后達到正常轉速時,應檢查軸承溫度是否正常(一般不宜高于80C)如發現風機有劇烈的振動,軸承溫度迅速上升及異常聲響等反?,F(xiàn)象時必須緊急 停機檢查。五、維護與保養5.1為了避免由于使用不當而引起的故障和事故發生,延長風機的使用壽命,必須加強風機的維護和檢修。5.2

6、風機進氣口前應裝過濾裝置或除塵器,若進氣口不安設備時,必須加防護網,以 防止異物吸入打壞葉輪。5.3定期清除風機及輸送管道內部的灰塵污垢。5.4定期更換潤滑脂。5.5根據下列故障產生原因進行檢修:a)風機劇烈振動1. 基礎的剛度不夠或不牢固。2. 進氣口與葉輪碰擦。3. 部件間或地腳螺栓聯接松動。4. 葉輪鉚接松動或葉輪變形。5. 進出氣口管道安裝不良,產生共振。6. 葉片積垢,磨損,葉輪變形,軸彎曲使轉子產生不平衡。7. 帶輪安裝不正,電機軸和風機軸不同心b)軸承溫度過高1. 潤滑脂失效或混入灰塵、砂粒等雜質。2. 軸承座、蓋聯接螺栓過緊或過松。3. 滾動軸承損壞。c)電流過大1. 氣體的密

7、度過大,使電機超載。2. 電網電壓太低或單相斷電。六、特別警示6.1 風機安裝完畢應使電機可靠接地。6.2 每次啟動風機時應嚴密關閉進氣風門,待轉動正常后才能開啟風門6.3 風機運行中嚴禁進入異物。9-19型離心通風機性能表機號No傳動方式 Type轉速speedr/min序號No流量Capacitym3/h全壓Pa軸功率Power of Shaft kW電動機Motor外型尺寸 長x寬x高SizeLXWX Hmm規格型號Type功率Power kW3.5A2840155228700.60Y80L-21.1373 x 588 x 631266728510.68374228340.7648102

8、8000.84593927600.92Y90S-21.56109826321.017123724981.118132523801.524A2900182435841.16Y90L-22.2435 X587X715297036651.333111636471.484126435971.645141035071.80Y100L-236155833841.977170432532.174.5A29001117446032.07Y112M-24489X561 X7822139746842.383161646722.684183945802.985206244473.296228142973.63Y13

9、2S2-25.57250441124.035A29001161056973.43Y132S2-27.5609 X734 X3682193257683.983225457404.504257656395.045284455175.546316653236.177348850806.86Y160M 1-2115.6A29001226271826.05Y160M 1-211638 X321 X9622271472327.023316772367.934361971098.885399669549.76Y160L-218.564448670910.8874901640012.09機號No傳動方式 Ty

10、pe轉速speedr/min序號No流量Capacitym3/h全壓Pa軸功率Power ofShaft kW電動機Motor外型尺寸 長x寬x高SizeLXWX Hmm規格型號Type功率Power kW6A29001278282988.55Y160M 2-215769 X900 X9892333984049.9133895836211.2044451821312.5454915803313.7865472775015.36Y160L-218.576028739017.076.3A290013220914910.91Y160L-218.5782 X925X108523865926512.65

11、34509921914.3045153905516.0055690885717.59Y200L 1-23066334854319.6076978814821.797.1D2900146101171719.83Y200L 2-2371230 X043 X278255321186822.99364541180725.99473761159629.09581441134031.98690661093535.63Y250M-255799881042639.628D2900165941503436.02Y280S-2751256 X1173 X428279131522941.75392321515147

12、.214105501487752.835116491454658.086129681402164.71Y315S-21107152871336271.958D14501329736204.5Y132M-47.51256 X1173 X2782395736655.223461636475.904527535846.60Y160L-4155582535077.266648433848.097714432318.99機號No傳動方式 Type轉速speedr/min序號No流量Capacitym3/h全壓Pa軸功率Power ofShaftkW電動機Motor外型尺寸 長x寬x高SizeLXWX H

13、mm規格型號Type功率Power kW9D14501469545978.11Y160L-4151289 X318 X18562563346559.4135672463210.6347511455111.9058294445313.08Y180L-42269233429714.58710171410116.2110D145016440584013.38Y200L-4301317 X464 X174827942549116.0339445589118.59410947574021.12512450549523.84613952524426.79Y225S-437715455495829.8811

14、.2D145019407736423.58Y225M-4451565 X641 X1947211158749128.25313269742832.76415380723637.22517491692742.02Y280S-475619602660947.21721713624652.666.8411.2D960159903182Y180L-6151565 X641 X19472738832378.203878532109.51410182312810.80511580299612.19612978286013.70Y200L 2-622714375275015.2812.5D145011257

15、7922940.84Y280S-4751603 X830 X2156215512939048.92318447931056.72421381906864.46Y315S-4110524316867872.76627251827881.75730186782291.18機號No傳動方式 Type轉速speedr/min序號No流量Capacitym3/h全壓Pa軸功率Power of Shaft kW電動機Motor外型尺寸 長x寬x高SizeLXWX Hmm規格型號Type功率Power kW12.5D96018327397511.85Y200L 2-6221603 X830 X1947210

16、270404314.20312213400916.46414156390718.71516099374121.11Y250M-637618042357123.72719985337726.4614D14501176701166871.97Y315M 1-41322031 X2050 X24002217931187486.223259161177199.9643004011464113.59Y315M 2-420053416310967128.2263828610457144.067424099878160.6914D960111690500420.89Y250M-6372031 X>05

17、0 X2400214428509025.02317158504729.01419888491732.97522618470937.21Y315S-675625348449441.81728078424946.6316D145012637715425140.31Y355M 3-43152091 X>340 X273523253115700168.0933868615563194.8944484115151221.4655099514488249.9816D960117463657040.72Y315S-6752091 X>340 X2735221538668348.783256136

18、62756.56429687645664.27Y315L 1-6110533762618072.55637837589881.52741912557592.929-26型離心通風機性能表機號No傳動方式 Type轉速speedr/min序號No流量Capacitym3/h全壓Pa軸功率Power of Shaft kW電動機Motor外型尺寸 長x寬x高SizeLXWX Hmm規格型號Type功率Power kW4A29001219838523.11Y132S1-25.5521 X711 *612236838203.283253637653.464270637843.655287736073.

19、866304435024.067321534074.294.5A29001313049105.51Y132S2-27.5642 X799 X8492340748635.873368547766.244396346616.64Y160M 1-2115423745457.066451544127.547479242567.985A29001429365039.12Y160M 2-215676X387X9372470659849.8035114586910.4845527572511.2355941555312.0066319538112.8176762518013.65Y160L-218.55.6

20、A290016032761016.09Y180M-222823X993X105326612754617.2737185740018.4747766721819.79Y200L 1 -23058346700021.1568919678122.5779500652724.056A290017419873622.72Y200L 1 -23028132866324.3838837849526.0849552828627.94510265803629.86610970778431.87Y200L 2-237711685749333.96機號No傳動方式Type轉速speedr/min序號No流量Capa

21、city m3/h全壓Pa軸功率Power of Shaft kW電動機Motor外型尺寸 長x寬x高SizeLXWX Hmm規格型號Type功率Power kW6.3A290018588969828.99Y225M-245967 X1117 X16729415961631.12310230942933.28411056919535.66511883861538.12612699893640.67Y250M-255713525831043.357.1A29001122921242750.27Y280S-2751317 X12259 X3612134751232156.5731464312078

22、60.494158261177664.84Y315S-21105170091145169.306181771105573.947193601063578.828D29001175841595595.72Y315M 1-21321349 X418 X152821927715818102.7332094715504109.8642264015112117.75Y315L 2-220052433214644125.8562600314177134.2872769613634143.148D145018792383411.96Y180M-418.51348 X418 X152829639380212.

23、84310473372913.73411320363814.72512166352915.73613001342116.79Y200L-430713848329417.899D1450112518486921.56Y200L-4301392 X594 X1691213723482823.14314913473624.75416118462023.53517322448138.35Y225M-445618512434330.25719717418132.24機號No傳動方式 Type轉速speedr/min序號No流量Capacitym3/h全壓Pa軸功率Power of Shaft kW電動機

24、Motor外型尺寸長x寬x高SizeLXWX Hmm規格型號Type功率Power kW10D1450117172614235.69Y250M-4551433 X1770 X870219319605639.19321465592043.02423612576147.10525758556051.35Y280S-475627905530955.35730052506559.3411.2D1450124126774762.90Y315S-41101694 X1983 X088227142763769.07330157746475.82433173726483.01536189700990.5063

25、9205669197.54Y315M-41327422216382104.5811.2D960115978334618.25Y225M-6301694 X1983 X088217969329920.04319966322522.00421963314024.09Y250M-637523959303126.26625956289528.31727953276330.3512.5D14501335409713108.91Y315M 2-41601755 X2212 X3122377329575119.603419259356131.304461179103143.75Y355M 2-4250550

26、3108782156.706545038381168.907586957993181.1012.5D960122206419731.61Y280S-6451755 X2122 X250224981412134.71327757402838.10430533392141.72Y315S-675533309378545.48636084361549.02738860345052.56機號No傳動方式Type轉速speedr/min序號No流量Capacitym3/h全壓Pa軸功率Power of ShaftkW電動機Motor外型尺寸 長x寬x高SizeLXWX Hmm規格型號Type功率Powe

27、r kW14D145014712112285191.94Y355M 2-42502199 X2418 X56225301112109210.7835890211830271.5JS-138-441046479211508297.357068211099324.167657210589349.378246310095374.514D960131197526255.70Y315S-6752199 X2481 X945235097518891.17338997507167.15Y315M 2-6110442897493673.52542796476480.15650696454986.3975459

28、6434192.6316D145017033916250439.1JSQ-147-4(3000V)5002271 X2830 X94527913116014482.238792315640529.4JSQ-158-4(3000V)85049671615210579.6510550014663631.8611430013983681.0712309013324730.216D9601465696911108.60Y355M 1-61852271 X2830 X9452523906813119.263582116659130.924640326481143.345698546254156.2567

29、56755971168.42Y355M 3-62207814965696183.5815丹徒糧機16丹徒糧機T HI A2 JUXTXx2x n"A4 "#丹徒糧機#丹徒糧機9-19、9-26型A式傳動離心通風機外形及安裝尺寸型號進風口法蘭出風口法蘭外形尺寸安裝尺寸D1D2D3聯結螺栓A1A2A3A4聯結螺栓E1E2E3E4B1B2abcn-M數量M數量x1 >nx2 Xn9-19-3.5160178199688611713216361436 X 335 X 458824854629539884801502504-159-19-41802052306898132148

30、18261442 X 340 X 4167228660033546594791902504-159-19-4.52002252506811215116019861445 X 344 X 4756.5322.5794472548108902203004-159-19-52282542846812516817121461450 X 348 X 4835356.5830472583121952303404-159-19-5.62502803108813918819924861456.3 X 354.5 X 494140110014956831361013404064-209-19-6.3258288

31、31888155210255310101466 X 362 X 410724501044530749153105.53804104-20口h-imA2 .uXIx2x nA4 :9-19、9-26型A式傳動離心通風機外形及安裝尺寸型號進風口法蘭出風口法蘭外形尺寸安裝尺寸D1D2D3聯結螺栓A1A2A3A4聯結螺栓E1E2E3E4B1B2abcn-M數量M數量x1 X1x2 Xn9-26-42282542846813620318425061455 X 357X 4724287832472570125992303404-159-26-4.52502903208815122620127661459

32、X 362.5 X 4810.53259004956961411053404064-209-26-52803203608816024521630861464 X 371 X 4903362945495753160110.5-3404064-209-26-5.63153553958818828023532861853 X 461 X 5100140211245107801801193704404-209-26-6.335539543510820230926236961859 X 468X 51123.5452.51247560940201127.54705504-24r9-19、9-26型D式傳

33、動離心通風機外形及安裝尺寸型號進風口法蘭出風口法蘭外形尺寸基礎尺寸D1D2D3n1 xd1A1A2A3A4n2 Xd2X1 XlX2 XlEFGKLMHabcdef9-19-7.12933203508-1017123223129214 >868 X366 X41774661042509123012782805204403005905101939-19-83403704008-1020027827034814 >880 X380 X42005251173572125614282805204403035905102079-19-94064505008-1021828929836914

34、>863 X466 X52265901318644128915862805204403105905102239-19-104505005508-1024432830438818 >869 X472 X52506561464715131717482805204403145905102399-19-11.250656062012-1027236737246718 X079 X483 X52807351641801156519473757006203667807002619-19-12.556062068012-1029740937748924 X086 X476 X6313820183

35、089516032156375700620372780700282型號各出風口 方向機殼中心高及基礎尺寸右0°右45 °右90 °右 135 °右 180 °右 225 °滾動軸承NijNijNijNjNijNij型號9-19-7.169022038063045035061045040058045040056045040053045045016169-19-877525046070048048067052044064052045061052046058052048016169-19-98602855207806005007606005

36、0072060055070060050065060058016169-19-1095032558087060060083565055080065055076065055072065060016169-19-11.2106038075098080068094080060090080070086080070081075075036209-19-12.51175410770108590070010359007009909007809458507809008208203620G9-19、9-26型D式傳動離心通風機外形及安裝尺寸型號進風口法蘭出風口法蘭外形尺寸基礎尺寸D1D2D3n1 Xd1A1A2A

37、3A4n2 Xd2X1 xnX2 xnEFGKLMHabcdef9-19-1463069075612-1233145743855722-1281 X86 >63509202050100120312400500900900478100010003369-19-1671077083616-1238452148462122-1288 X482 X40010502340114420912735500900900488100010003729-26-71223735429641420-1068 X465 >623763912595091317136928052044

38、03275905102429-26-84565005508-1226839832845820-1075 X472 >62627201418574134915282805204403345905102639-26-950656061012-1228344737352720-1082.5 X480.5 X2948101594646139216992805204403465905102869-26-1056662068612-1233249838955620-1089 X488 >6327900177071714331870280520440353590510309型號各出風口 方向機殼中心高及基礎尺寸右0 °右45 °右90 °右 135 °右 180 °右 225 °滾動軸承NijNijNijNjNijNij型號

溫馨提示

  • 1. 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
  • 2. 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
  • 3. 本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
  • 4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
  • 5. 人人文庫網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
  • 6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
  • 7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。

最新文檔

評論

0/150

提交評論