BalluffIOLINK模塊配置

1、打開web瀏覽器，輸入IP地址，進入web配置界面BALLUFFBMI PNT-50&-105-Z015Modulo Information&m PMT-50B-105-ZQ15Order Codfl!HNtQQSHName:Contact:73765 Neuhausen 匕GermanvBaauff GinbHFirmware Revision i3.2Hardwars REuision;bnipnt5OBEP Address.!1-92.160.0.6Subnet Flasks255.Z55.25S.OGateway Address;192.168,6MAC Address

2、:00:19:2132： IC ：3SLink Speed Port 1:100 Mbit/5 FULLLink £曄d Port 2：Nd LinkPLC Lock：竄耳國早d“ SeSboF點擊登錄按鈕輸入登錄密碼:BNIPNT3ALLUFFBN I PNIT-5O8-105-ZO15Log HiBNIPINT5 required for Configuration operations on the Fiddbus Master or the ICkLink Devices.You will be logged out after 5 minutes： automaticall

3、y.HDime sorts OOD登錄成功，如下圖BALLUFFBNI PNT-508-105-Z015A 1 O H iPortii I0DD Log-aul Config SgInfoLogoutSuccessfully Dogged in.點擊菜單欄8崎目，進入?yún)?shù)配置界面BALLUPFBNI PN7-508-105-Z015Home Ptirhs. 30 DDMDtSuIe CDnfiquratiDriNa me:?Location:73765 Mg uh mu 工an a.d.FiS GermanyContacLrBalluF GmbHPort ConfiguratiDriiPinM

4、odeIO Link亨Digital Input 二JSet PortsSave CnnfigurationReboot Factcifv RfiEgt點擊左下角的Set Ports按鈕，打開IO-Link功能Port ConfigurationPin10 Link,ModeDigital InputDigital inputT10 LinkPj10 LinkTDigital InputT10 LinkTDigital InputTPinMode10 Link臼Dig/al Input,10 Link臼Digital Input7IQUnkDigital Input10 LinkDig也al

5、InputSet Parts點擊菜單欄01,進入通道設置界面，可以配置HubBALLUFFBNI PNT-508-1Q5-ZOL5IO -Link Device Properties (Part 0)DX037BJdmtrfiution DotaVQrd&rlDsID;Vendor Nfn?：nd&T»H：Arcdurt Name:Product ID：Produci Tflxc：GqnR H jmbfir!Hindware Re'isi4ri；RrmHina 由原工日tdn specific H0x050 SCO喇IJFhcra/wwrf .balluffi

6、com 時UECL-n2MK0 噸 BMKJ07ZSnwi/Ajnor Nib H£ 21.3IS： 33:Process OfftaTroutsFF FFOiiOLIS (k*a£)=DD OliParainwtcrs£ndax=Sutindex:;。犯卜小比 Rd Write Apai1r CtearIndex地址85為Hub擴展通道定義ParametersIndex:Subindex:Data Chex):Result:85口00OK Read ©Write ：Apply Clear00表示關閉ParametersIndex:Subindex:Da

7、ts (hex):Re suit;B5|01OKO Read Write Apply Clear01表示打開Index地址65為Hub DI/DO的配置定義FF FF FF FF 表示兩個 Hub 全部配置為輸出(Hub1-14DO, Hub2-16DO)ParametersIndex:65Subindes:CData (hex);FF FF FF FFResult:OK0 Read Write ApplyCl吧日下圖表示第一個Hub為14個DI,第二個Hub為16個DOParametersIndex:6SSubindex:口Data fhex:):OD 00 FF FFResujlt:OKRead . 'Write Apply Clear下圖表示第一個Hub為14個DO,第二個Hub為16個DIa Read ")WriteClearParametersIndex:Subindex:Data (hex:):Result:具體輸入輸出定義分配指示如下圖:Parameter DataIndex:Subindex:Data (hex): Result!EventsCurrent Event:Parameter server