全尺寸.part1mp點報告

1、CHECK RESULT 檢查結果OK.RATIOTitle 項目Part codeP1P2P3TOTAL全尺寸OK Ratio100%OK Pos10Total Pos10SURF.型面OK Ratio100%OK Pos6Total Pos6TRIM修邊OK RatioOK PosTotal PosHOLE孔位孔徑OK Ratio100%OK Pos4Total Pos4Title 項目Content 內容CS11_Fully measured ReportProject Name 項目名稱CX11Part Code 零件號CAD NumberCAD 號-010Part Name 零件名稱

2、HINGE REINFORCEMENT LOWER FR LHTie1r 供應商Toolingr 模具供應商tianyueMaterial standard code 板材牌號VDA 239-CR240LAActual Material 替代牌號Thickness 板材厚度1.2Coating thickness 鍍鋅層厚度GI50/50Detection time 檢測日期2016.12.21RPS InformationStep 1 : MP CheckingStep 2 : Hole size CheckingSD099H2LSD992H3LSD992H1Lnominal10.+0.15

3、/-010.0+0.22/-06.52+0.22/-0actual10.1410.216.71deviationStep 3 : ThinningREPORT CHECKING THINNESMeasure thickness request: 1.2 mmactual thickness 1.2 mmLIMITS MAX : 20%11.181.7%21.172.5%31.163.3%41.181.7%51.181.7%61.172.5%71.163.3%8910111213141516THINNING MAXStep 4 : Appearance CheckingAppearance Ch

4、ecking 外觀檢查NO判定標準 Control standard檢驗方法 Methond判定 OK、NG、N/APicture1零件是否正確？ Is the rignt part?Visual目視OK2變薄率是否 料厚的 20%范 內？ THINNING MAX no more 20%Venire caliper 游標卡尺OK3是否有開裂、暗裂？ No crack,deformationVisual目視OK4毛邊、毛刺、尖角是否 0.3mm 范圍內？ glitches, indenion,damaged,Venire caliper 游標卡尺OK5是否有模痕、壓傷（無手感可接受）？ No

5、roughness detect with the handwith the handOK6是否有拉傷、劃傷？No degradation or deformation手觸 with the handOK7是否有起皺、變形（裝配面平面度需 0.2MM 以內）？No crack,deformationVisual /Venire caliper目視/游標卡尺OK8是否有生銹？Rust?Visual目視OK9字印是否正確、明顯且無手 感？Marking information crrect ?Visual/ with the hand目視/手觸OK10公差是否與 3D 公差相符？ Report tolerance is the same with 3D?檢查 checkingOK11零件定位是否與檢具定義相符？ PRS is the same with gauge?檢具 gaugeOK12料邊斷差是否超過公差帶的 50%？ Trim no moren 50% out of tolerance?目視