電池常用專業術語-中英語

1、,序號 首字母 英文 中文,1 A aging 老化,2 B battery charger 充電器,3 black-fleck 黑斑,4 C cap 蓋板,5 capacity density 能量密度,6 capacity grading 分容,7 cathode tab welding 極耳超焊,8 cell 電芯,9 charge(capacity) retention 荷電（容量）保持,10 checking code 檢碼,11 concave spot 凹點,12 constant current charge 恒流充電,13 constant current discharge

2、 恒流放電,14 constant voltage charge 恒壓充電,15 corrective measures 糾正措施,16 crack 裂紋,17 cut-off voltage 終止電壓,18 cycle life 循環壽命,19 D dark trace 暗痕,20 degrade 降級,21 dent 凹痕,22 discharge depth 放電深度,23 distortion 變形,24 drape 打折,25 E Electrical and MechanicalServices Department 機電部,26 electrolyte 電解，電解液,27 emp

3、aistic 壓紋,28 end-off voltage 放電截止電壓,29 environmentally friendly 對環境友好,30 equipment first inspection 設備首檢,31 erode 腐蝕,32 explosion-proof line 防爆線,33 F first inspection 首檢,34 formation 化成,35 fracture 斷裂,36 I inspection 檢驗,37 insulate 絕緣,38 internal resistance 內阻,39 J jellyroll 卷芯,40 joint 接縫，結合點,41 L

4、laser deflecting 偏光,42 laser reticle 激光刻線,43 laser welding-flatwise weld 激光焊接-平焊,laser welding-standing weld 激光焊接-立焊,44 leakage 漏液,45 leak-checking 測漏,46 leaving out of welding 漏焊,47 limited charge voltage 充電限制電壓,48 local action 自放電,49 M margin turnly 翹邊,50 measuring the dimension of cells 電芯卡尺寸,51

5、meet requirement 達到要求,52 memory effects 記憶效應,53 N nick 劃痕,54 nominal voltage 標稱電壓,55 notice-board confirmation 看板確認,56 nugget 硬塊,57 O obverse 正面,58 open circuit voltage 開路電壓,59 over charge 過充,60 over discharge 過放,61 over the thickness 超厚,62 P particle 顆粒,63 PE membrane PE膜,64 pit 坑點,65 placing cells

6、 into the box 電芯裝盒,66 point inspection 點檢,67 preventive measures 預防措施,68 pricking the tapes 扎孔,69 process inspection 制程檢驗,70 put the battery piled up 將電芯疊放在一起,71 Q qualified products 合格品,72 quality assurance 質量保證,73 quality control 質量控制,74 quality improvement 質量改進,75 quality match 品質配對,76 quality pl

7、anning 質量策劃,77 R rated capacity 額定容量,78 recharge 再充電,79 refitting the can of cell 電芯殼口整形,80 requirment 要求,81 reverse 背面，反面,82 rework 返工,83 ringing cells into pyrocondensation films 套熱縮膜,84 S safety vent 安全閥,85 sand aperture 砂眼,86 scar 疤痕,87 secondary battery 二次電池,88 select appearance 選外觀,sharp-set 批

8、鋒,89 short circuit checking 測短路,90 smudginess 污物,91 spot welding by laser 激光點焊,92 spot welding place 點焊位置,93 spraying the code 噴碼,94 spur 毛刺,95 sticking the PVC cover boards 貼面墊,96 storing 陳化,97 storing with high voltage 高壓儲存,98 T tabs deflection 極耳歪斜,99 tabs excursion 極耳錯位,100 technics requiment 工藝

9、要求,101 U ultrasonic welding 超聲波焊接,102 ultrasonic welding strength 超焊強度,103 unqualified products 不合格品,104 W wave 波浪,105 working procedure 工序,Voltage：,Units of measuring electrical current, all batteries are rated in volts DC. (Direct Current). This determines how much energy is needed to power your e

10、quipment.,Voltage plateau:（電壓平臺）,A slow decrease in voltage over a long period of time. As a rule, the plateau extends from the first voltage drop at the start of the discharge to the bend of the curve after which the voltage drops rapidly at the end. ,Nominal Voltage（標稱電壓）,The voltage of a battery,

11、 as specified by the manufacturer, discharging at a specified rate and temperature. ,Working voltage（工作電壓）,The working voltage of a cell or battery begins at its electrical connections as soon as an electrical consumer is connected to it.,Discharging voltage, average voltage (放電電壓) ,The average disc

12、harging voltage is the average value of the discharging voltage during the entire discharging process with a related discharging current.,Open circuit voltage (OCV開路電壓), The voltage of a battery when there is no current flowing.,Closed-Circuit Voltage (CCV閉路電壓),The potential or voltage of a battery when it is discharging or charging.,State of charge: ,The rate of charge capacity vs. whole capacity.,Initial voltage（起始電壓） ,A batterys initial voltage is the working voltage when discharging begins. ,End-point voltage (End voltage, Cutoff voltage, Final voltage)截止電壓,Specified closed