電氣試驗記錄表格

1、母線安裝記錄Bus installation record項目：Project裝置：Unit工號：Sectio n名稱Name施工日期Date電壓等級VoltagekV圖號Drawing No.母線型號、規格 Bus model and spec.套管、絕緣子型號Bushing insulator model1、一般安裝檢查：General installation inspection序號No.檢查調整項目Inspection and adjustment item安裝檢查結果Inspection result1母線型號、規格、材質核對Bus model, spec, and mat. In

2、spectionP號規格材質ModelSpecificationMaterial2絕緣子、穿墻套管檢查Insulator and lead-in insulator型號規格油位、密封絕緣ModelOil level, sealInsulation3母線支架制作安裝Bus support fabrication and installation規格安裝尺寸防腐Spec.DimensionAnti-corrosion4母線安裝檢查Bus installation排列、相色彎曲倍率伸縮節Arrangement, colorCurve radiusExpansion joint5連接螺栓、墊圈檢查Bo

3、lt and washer inspection規格熱鍍鋅露出長度Spec.GalvanizationLeft length6母線接觸面Bus contact area inspection光潔平整搪錫電力復合脂Smooth.Enam.Polymer7硬母線焊接檢查Rigid bus welding inspection焊工合格證號Weldor No.8軟母線、組合母線安裝Flexible and combine bus installation2、母線接Bus conta（觸面連接緊密檢測：ct. Tightness inspection螺栓規格 （mmBolt spec.實測力矩值（N.m

4、）Actual torque螺栓規格 （mmBolt spec.實測力矩值（N.m）Actual torque螺栓規格 （mmBolt spec.實測力矩值（N.m）Actual torque最小值Min.最大值Max.最小值Min.最大值Max.最小值Min.最大值Max.3、軟母線弛度：Flexible bus sag inspection軟母線名稱Flexible bus name設計弛度（mr）Design sag實測弛度（mmActual sag4、母線相同、對地最小距離檢測：Bus phase and phase to earth min. Distance measure母線類別

5、Bus type主母線Main分支母線Branch實測最小相間距離（mmMin. Phase to phase distance實測最小對地距離Min. Phase to earth distance備注：Remarks結論：Conclusion技術負責人Check施工人Operator蓄電池充（放）電記錄 Storage battery charging/Discharging record項目Project裝置：Un it工號：Sectio n名稱Name型號Model岀廠日期Manuf. Date電壓VoltageV容量capacityAh電池總數Number of battery電解液

6、Electrolyte電解液化驗單或合格證號Electrolyte report or certification No.蒸餾水化驗單或合格證號Distilled water report or certification No.注入時電解液溫度Electrolyte temp. at fillingc電解液比重Specific gravity of electrolyte開始注入時間Filling start time結束時間End time初充電First charging充電開始時間Charging start time結束時間End time單獨補充充電的電池編號Separately

7、charged cell No.放電Discharging放電開始時間Discharge start time結束時間End time放電電流Discharge current放電容量Discharging capacity為額定容量的% （換算到25C時）% of rated capacity （at 25 C）充（放）電特性曲線圖：（充放電記錄見附表）Charging/Discharging characteristic curve備注：Remarks結論：Conclusion技術負責人Check施工人Operator蓄電池充（放）電 記錄附表Attached table for stor

8、age battery charging/Discharging record項目Project裝置：Unit工號：Sectio n名稱Name型號Model岀廠日期Manufacture date電壓VoltageV容量CapacityAh電池總數Number of battery時間Time充（放）電 電壓（V）Charge/Discharge voltage充（放）電 電流（A）Charge/Discharge currentNoNoNoNoNoNoUDTUDTUDTUDTUDTUDT技術負責人Check施工人Operator日期Date電機抽芯檢查記錄Motor loose-core

9、inspection record項目Project裝置：Un it工號：Secti on名稱Name位號Tag. No.檢查日期Inspection Date型號Type額定容量Rated capacitykW額定電壓Rated voltagekV額定電流Rated currentA接法Connection絕緣等級Insulation class轉速Rotation speedr/min轉子結構Rotor structure防爆等級Explosion proof class岀廠編號Manufacturer No.制造廠Manufacturer防護等級Prevention class檢查內容I

10、nstallation contents標記Mark備注Remark鐵芯軸頸無傷痕銹蝕No Damage & corrosion on surface of core shaft滑環和換向器無傷痕、銹蝕No Damage & corrosion on surface of commutator and slip-ring繞組絕緣層完好，綁線無松動Winding insulation coating and fixing inspection繞組連接正確，焊接良好Winding connection and welding inspection繞組電阻檢測合格Winding resistance

11、 inspection定子槽楔無斷裂凸岀及松動，端部槽楔牢固Stator slot wedge inspection轉子平衡塊緊固，平衡螺絲鎖車Rotor balance block and bolt fixing inspection風扇完好，方向正確Fan inspection磁極及鐵軛固定良好Magnetic pole and hub fixing inspection勵磁繞組緊固Exciter winding fixing inspection鼠籠式電機轉子導電條和端環焊接良好，澆鑄無裂紋Rotor conductor and end link of squirrel-cage motor軸承滾動體與內、外圈轉動靈活無松動、卡澀Bear