塑料件卡扣等設計標準模塊自創推薦新人學習演示文稿

塑料件卡扣等設計標準模塊自創推薦新人學習演示文稿現在是1頁\一共有33頁\編輯于星期一優選塑料件卡扣等設計標準模塊自創推薦新人學習現在是2頁\一共有33頁\編輯于星期一3目錄1.柱位結構······································································3

優缺點及使用范圍······················································42.螺釘沉孔·······································································5

優缺點及使用范圍·······················································63.

帶罩蓋的螺釘沉孔····························································7

罩蓋········································································8

優缺點及使用范圍·······················································94.金屬卡口支撐臺（單邊卡位）··············································10

雙邊卡位··································································11

金屬卡口··································································12

優缺點及使用范圍·······················································135.椅背板鋼絲卡·································································14

優缺點及使用范圍·······················································156.鋼絲卡··········································································16

優缺點及使用范圍·······················································177.平板卡口連接··································································18

結構分析··································································19

優缺點及使用范圍·······················································208.卡口連接與翻邊·······························································21

結構分析··································································22

優缺點及使用范圍·······················································239.插片式卡口連接·······························································24

結構分析·································································25

優缺點及使用范圍······················································2610.圣誕樹支撐···································································27

優缺點及使用范圍·····················································28

圣誕樹例樣······························································2911.塑料支腳·····································································33

優缺點及使用范圍······················································34

現在是3頁\一共有33頁\編輯于星期一4柱位的設計方式-自攻螺釘自攻螺釘規格（國標）螺釘柱內徑?（mm）nd螺釘柱外徑（mm）wdST2.21.75ST2.92.36ST3.52.87ST4.23.47.5ST4.83.88ST5.54.49自攻螺釘?shù)臉藴食叽绫韮?nèi)值為參考值，一般柱位內徑較nd大0.3~0.4mm，柱位壁厚在1.25mm左右，以防止產品表面縮凹。柱位高一般在5～10mm?，F(xiàn)在是4頁\一共有33頁\編輯于星期一5柱位結構的優缺點及適用范圍用途：將零部件（開關盒，鉸鏈等）固定到塑料件上。優點：結構簡單，固定牢固。缺點：產品表面容易縮凹，裝配工序較煩。適用產品：旁側板等需要固定零部件的塑料件。現在是5頁\一共有33頁\編輯于星期一6DB_PART_NOOS_PART_NAMEstdKdkI

1ST2.22.21.646.52ST2.92.92.45.69.53ST3.53.52.679.54ST4.24.23.189.55ST4.84.83.79.5136ST5.55.541113螺釘沉孔自攻螺釘?shù)臉藴食叽鐂td為螺釘螺紋處直徑；K為螺釘頭部厚度；dk為螺釘頭部直徑；l為螺釘螺紋處長度；t為產品壁厚；Δ根據公差要求進行設定。現在是6頁\一共有33頁\編輯于星期一7螺釘沉孔的優缺點及適用范圍用途：用螺絲固定塑料件。優點：裝配簡單,可拆卸,定位性好。缺點：裝配位可見，容易粘定模導致產品拉壞。適用產品：適用于大部分塑料件的非可見區，如設在可見區，必須得到客戶同意。粘定模對策現在是7頁\一共有33頁\編輯于星期一8帶罩蓋的螺釘沉孔H<1.5D,定模側壁脫模斜度大于5度。此標準件為裝配件，裝配后蓋子與本體要求無間隙、晃動、斷差，且紋理一致?，F(xiàn)在是8頁\一共有33頁\編輯于星期一9罩蓋現在是9頁\一共有33頁\編輯于星期一10帶罩蓋的螺釘沉孔的優缺點及適用范圍用途：用螺絲固定塑料件,并遮蓋孔位。優點：裝配簡單,可拆卸,定位性好，看不到螺釘。缺點：容易粘定模導致產品拉壞，多一道裝配工序，表面有縫隙。適用產品：適用于大部分塑料件一般要求外觀面，使用時必須得到客戶同意?，F(xiàn)在是10頁\一共有33頁\編輯于星期一11金屬卡扣支撐臺（單邊卡位）h=H-6.5(當H<=20時)；

h=0(當20<H<=30時);h=13.8(當30<H時)?，F(xiàn)在是11頁\一共有33頁\編輯于星期一12金屬卡扣支撐臺（雙邊卡位）單邊卡位受法向力時金屬卡扣可能歪斜。雙邊卡位受法向力時金屬卡扣可能會拉斷塑料件?，F(xiàn)在是12頁\一共有33頁\編輯于星期一13金屬卡扣可拆卸式卡扣不可拆卸式卡扣現在是13頁\一共有33頁\編輯于星期一14金屬卡扣支撐臺的優缺點及使用范圍用途：裝配CLIP后使塑料件固定在金屬板上。優點：裝配簡單，可承受法向拉力及壓力，高度調節范圍大。缺點：裝配后有一定晃動量，對切向受力抵抗弱。適用產品：旁側板、前擋板等塑料件，位置較自由?，F(xiàn)在是14頁\一共有33頁\編輯于星期一15椅背板鋼絲卡扣詳細請參照圖紙其他規格鋼絲可參照此形狀適當更改。H值一般在20mm左右?，F(xiàn)在是15頁\一共有33頁\編輯于星期一16椅背板鋼絲卡扣的優缺點及適用范圍用途：用鋼絲固定塑料件。優點：裝配簡單,可拆卸,位置可適當調節。缺點：定位差，需靠其他定位機構輔助。適用產品：椅背板上端，一般于左右上角設2處。現在是16頁\一共有33頁\編輯于星期一17鋼絲卡扣其他規格鋼絲可參照此形狀適當更改，開口尺寸在鋼絲直徑的60％左右。現在是17頁\一共有33頁\編輯于星期一18鋼絲卡扣的優缺點及適用范圍用途：用鋼絲固定塑料件。優點：裝配簡單,可拆卸,模具上易實現。缺點：高度有限制,受力有脫落可能。適用產品：旁側板、前擋板等塑料件，卡扣周圍50mm左右范圍內無發泡或面套擠壓?，F(xiàn)在是18頁\一共有33頁\編輯于星期一19平板卡扣連接現在是19頁\一共有33頁\編輯于星期一20平板卡扣連接－－結構分析現在是20頁\一共有33頁\編輯于星期一21平板卡扣連接的優缺點及適用范圍用途：平板件與其他塑料件利用卡扣連接。優點：裝配簡單且牢固，適用性強。缺點：需要其他結構支撐板件。適用產品：適用于板件與一般塑料件的連接等，板件一般不屬于重要外觀件。現在是21頁\一共有33頁\編輯于星期一22卡扣連接與翻邊現在是22頁\一共有33頁\編輯于星期一23卡扣連接與翻邊－－結構分析現在是23頁\一共有33頁\編輯于星期一24卡扣連接與翻邊的優缺點及適用范圍用途：塑料件之間的相互固定。優點：裝配簡單且牢固，適用性強，對內部結構起到遮蔽作用。缺點：受法向拉力有限，翻邊易損。適用產品：適用于各種塑料件的相互固定，例如外側飾板與內側飾板的連接、扶手盒的結合等?，F(xiàn)在是24頁\一共有33頁\編輯于星期一25插片式卡扣連接現在是25頁\一共有33頁\編輯于星期一26插片式卡扣連接－－結構分析現在是26頁\一共有33頁\編輯于星期一27卡扣連接與翻邊的優缺點及適用范圍用途：塑料件之間的相互固定。優點：結構簡單,裝配容易，空間占用小。缺點：受力易脫落，需和其他卡扣配合使用。適用產品：例如外側飾板與內側飾板的連接等。現在是27頁\一共有33頁\編輯于星期一28圣誕樹支撐臺圣誕樹現在是28頁\一共有33頁\編輯于星期一29圣誕樹支撐臺的優缺點及適用范圍用途：利用圣誕樹來防止外表面浮起(提供法向拉力)。優點：裝配簡單,可拆卸,模具上易實現。缺點：安裝后高度不穩定,對切向受力抵抗弱。適用產品：旁側板、椅背板等塑料件?，F(xiàn)在是29頁\一共有33頁\編輯于星期一30零件號零件名稱D1D2L1L2ApplicationForcerequirement1442633W-CLIP-PLASTICW型塑料卡子

51814.32Hole:Φ9.0±0.12

Thickness:2.75mmInsert≤80N

Extraction≥334N圣誕樹例樣現在是30頁\一共有33頁\編輯于星期一31零件號零件名稱D1D2D3L1L2L3L4L5ApplicationForcerequirement1325904CB－07000－00CLIP塑料夾子

154.66.819.31.310.816.6Hole:Φ7.0+0.1

Thickness:1.5-3mmInsert≤150N

Extraction≥200N現在是31頁\一共有33頁\編輯于星期一32零件號零件名稱D1D2D3d1d2d3L1L2L3ApplicationForcerequirement1116415A-StyleXmasTreeClipA型塑料釘

3229.24863.12.81.72.75Hole:Φ7.0-7.25

Thickness:2.75±0.15mmInsert≤8LBF

60LBF≥Extractio