WOHA33_1037 new223_228_AT-472143-710-801

Hong Kong Airlines Limited香港航空03110-01Hong Kong Airlines MEDHong Kong Airlines LimitedWO NO/工作指令號SEQ NO/序列號WOHA331037_228_223適航指令(AD) 培訓方式1037223通用類/GenericTitleOperational Check of Dual Flow Shut Off Valve (DFSOV), Dual Flapper Check Valve (DFCV) and Nitrogen-Enriched Air (NEA) Pipeline for LeaksMcd&Rev/廠家工卡&修訂日期標題操作檢查雙流量關斷活門（DFSOV），雙碟形單向活門（DFCV）和富氮管有無滲漏AMM 472143-710-801 2014-10-01A/C/飛機號Subtask No/工卡號JC Rev/工卡版本號Workarea/工作區域Skill/工種Man Hour/工時BLNLAT-472143-710-801HR000001機身/AirframeAIRP01:36MP Item/MP號Baseline/依據MP REV/ MP版本號Station/維修站Threshold/首檢Interval/重復檢HA33-470000-03-1MPD 470000-03-1,ALS PART 5,FAL 470000-00001-1-F,AD 2012-0168Issue 2 Revision 4SHA12000 FH12000 FHAccess Panels/接近蓋板Zones/區域Written/編寫Approved/批準191KB1912014-11-262014-11-26TOOLS/工具TOOLS NECESSARY/必須工具ITEM項目P/N件號DESCRIPTION名稱EQTP類型QTY數量APP適用性Conditions note互換信息及備注198A24403000000CABLE HOLDING STRAPTO1ALL(必需/Necessary)298D47209001000PRESSURE & VACUUM TESTER, IGGSTO1ALL(必需/Necessary)TOOLS IF NECESSARY/視情工具ITEM項目P/N件號DESCRIPTION名稱EQTP類型QTY數量APP適用性Conditions note互換信息及備注1CML11-003丁酮METHYL-ETHYL-KETONETO1ALL(視情/As Necessary)298A52107632000PIN - SAFETY SLIDETO1ALL(視情/As Necessary)398A53003500000REMOVAL TOOL OF PHILLIPS TORQ-SET FASTENERTO1ALL(視情/As Necessary)498F57103001000SLEEVE,PROTECTIVE-CARBON RODSTO1ALL(視情/As Necessary)598F52003002001A319/A330/340艙門攔網TO1ALL(視情/As Necessary)698A57304002000EXTRACTION, MANHOLE BOLTTO1ALL(視情/As Necessary)798F53008792000DEV-INST,DRY SEAL FLOOR PANELTO1ALL(視情/As Necessary)8DLTFRPSKT3028AREPAIR KIT FIELD - SIZE 04 TO 24TO1ALL(視情/As Necessary)998F21001004001EQUIPMENT,R I-PACK EXCHANGERTO1ALL(視情/As Necessary)PARTS AND MATERIAL/航材NOTE:OPERATOR MUST GET AND INSTALL THE PARTS THAT CORRESPOND TO THE RELATIVE WORKORDER NO.注釋?zhuān)赫?qǐng)工作者嚴格按照工作指令號領取預定的航材裝機PARTS AND MATERIAL NECESSARY/必須航材ITEM項目P/N件號DESCRIPTION名稱EQTP類型QTY數量APP適用性Conditions note互換信息及備注PARTS AND MATERIALIF NECESSARY/視情航材ITEM項目P/N件號DESCRIPTION名稱EQTP類型QTY數量APP適用性Conditions note互換信息及備注1MS24665-153(32A3)PINAS3ALL(視情/As Necessary)2M25988-1-904(73A6)PACKINGAS2ALL(視情/As Necessary)3MS24665-151PINAS4ALL(視情/As Necessary)4MS24665-152COTTER PINAS1ALL(視情/As Necessary)5MS24665-86(32A3)PINAS1ALL(視情/As Necessary)6MS24665-172PIN-COTTERAS3ALL(視情/As Necessary)7NSA8203-008O-RINGAS1ALL(視情/As Necessary)8NSA5050-3NUTAS8ALL(視情/As Necessary)9MS9021-226PACKING-PREFORMEDAS1ALL(視情/As Necessary)10CML11-004CLEANERCH1ALL(視情/As Necessary)11ABS1040-56(32A2)SEALAS4ALL(視情/As Necessary)12A5217026320000PLATE-LOCKINGAS1ALL(視情/As Necessary)13NSA8203-222O-RINGAS1ALL(視情/As Necessary)14MS16624-5015-1RINGAS2ALL(視情/As Necessary)15CML16-018Top Coat Polyurethane - CA8000/XXXXCH1ALL(視情/As Necessary)16CML09-018BLOW ADHESION POLYSULFIDE SEALANTCH1ALL(視情/As Necessary)17F9241130620000SEALAS2ALL(視情/As Necessary)18CML16-001CANTI-CORROSION PRIMER 4355/3600+0701/9000+0433/9000CH1ALL(視情/As Necessary)19ABS5800D080BSEALAS4ALL(視情/As Necessary)20ABS5800B024BSEALAS7ALL(視情/As Necessary)21M259881-222O-RINGAS6ALL(視情/As Necessary)22M259881-219O-RINGAS2ALL(視情/As Necessary)23CML06AAB1SEALANTCH1ALL(視情/As Necessary)24CML04TMB2primerCH1ALL(視情/As Necessary)25CML06AAC1INTERFAY SEALANTCH1ALL(視情/As Necessary)26CML12ABC1CORROSION PREVENTIVE COMPOUND, TEMPORARYCH1ALL(視情/As Necessary)27CML06ABA1FUEL TANK BRUSH CONSISTENCYCH1ALL(視情/As Necessary)28CML08BAA9SOLVENT GENERAL PURPOSECH1ALL(視情/As Necessary)29CML14SBA1CLEANING ABSORCH1ALL(視情/As Necessary)30CML03FAB1VASILINECH1ALL(視情/As Necessary)31CML06ABB1FUEL TANK SEALANT POLYSULFIDECH1ALL(視情/As Necessary)32CML06LCG9SINGLE PART CHROMATED JOINTED COMPOUNDCH1ALL(視情/As Necessary)或CML12ABE233CML06AAA1SEALANTCH1ALL(視情/As Necessary)34CML10ABC1CHEMICAL CONVRSN COATING YELLOW ALUMINUMCH1ALL(視情/As Necessary)35CML04JME4TOPCOAT GREY (INTRNL APPLIC.)CH1ALL(視情/As Necessary)36CML03HBD9GREASECH1ALL(視情/As Necessary)37CML05EML7EPOXY ADHESIVECH1ALL(視情/As Necessary)38CML06BQD1SILICONE SEALANTCH1ALL(視情/As Necessary)39CML06CMD9SEALANTCH1ALL(視情/As Necessary)40CML14QFB1LOCKWIREAS1ALL(視情/As Necessary)41CML04EAC2ANTI-CORROSION PRIMER (POLYURETHANE)CH1ALL(視情/As Necessary)42CML12ABE2Corrosion inhibiting compoundCH1ALL(視情/As Necessary)43CML14QDB1LOCKWIREAS1ALL(視情/As Necessary)44CML06AEB2SEALERCH1ALL(視情/As Necessary)45CML06HAA1BRUSHABLE FUEL RESISTANT COATINGCH1ALL(視情/As Necessary)46CML12ACC1Corrosion Preventive CompoundCH1ALL(視情/As Necessary)47CML04CMA2WASH PRIMER(0434/9000+0841/9000+7641/3600)(Metaflex FCR Pri)CH1ALL(視情/As Necessary)48CML03GBB1GREASECH1ALL(視情/As Necessary)49CML14JAB1SILICONE FORAMCH1ALL(視情/As Necessary)50CML06ACA1SEALANT, LOW DENSITY-FUEL TANK AND GPCH1ALL(視情/As Necessary)51CML06PAG1POLYSULFIDE SEALANT ADHESION PROMOTERCH1ALL(視情/As Necessary)52CML05DBB1AdhesiveCH1ALL(視情/As Necessary)53CML05PCB2AdhesiveCH1ALL(視情/As Necessary)54CML05RAM1TAPECH1ALL(視情/As Necessary)55CML12ACB1Corrosion Preventive CompoundCH1ALL(視情/As Necessary)56CML05RDA1Adhesive Film TapeCH1ALL(視情/As Necessary)57CML03GEE1Synthetic Oil base Grease - Fuel and Oxidized Environment FlCH1ALL(視情/As Necessary)58CML14JAD1TAPE, SELF-ADHESIVECH1ALL(視情/As Necessary)59CML05BAA1SEALANT, ANAEROBICCH1ALL(視情/As Necessary)60CML05RMM9MOISTURE BARRIER FOIL,SELF ADHEISIVECH1ALL(視情/As Necessary)61CML05JBB9SOLVENT BASED NITRILE RUBBER ADHESIVECH1ALL(視情/As Necessary)62CML05NCA2ADHESIVE TAPECH1ALL(視情/As Necessary)63CML14RCB1PVCCH1ALL(視情/As Necessary)64CML12AHA1corrosion preventive filler compoundCH1ALL(視情/As Necessary)65MS24665-150PINAS1ALL(視情/As Necessary)IMPORTANT NOTE:In the event of any discrepancies between the Chinese instruction and the English instruction, the English procedure should prevail.Record Additional Work/Findings(If Applivable) Reference No. Certificate of Release to Service (* Tick as appropriate # Different crews should perform the work on each of the systems)Certifies that the work specified, except as otherwise specified, was carried out in accordance with HKAR-145and in respect to that work, The aircraft / aircraft components are considered ready for Release to Service. HKA Approval No: AI / 135 / 706 * HNAT Approval No.: JMM 076, D3039 * HNAT Approval No.: JMM 047, D101115* HNAT Approval No.: JMM 049, D500023 * CASL Approval No: AI / 101 / 798 * TAECO Approval No.: DAI / 89 / 1295 * HAECO Approval No: DAI / 1 / 853 * SIAEC Approval No: AWI / 01 * STARCO Approval No.: JMM 039, D.200078 * SMECO Approval No: JMM 081, D.400009 * AMECO Approval No.: JMM001,D101131* Other: * Signature:_ Authorization No.:_ Date:_AT-472143-710-801 HR000001 W/O:1037 AC:BLNL頁碼，4 / 14工卡Job card:HA33-470000-03-1TITLEOperational Check of Dual Flow Shut Off Valve (DFSOV), Dual Flapper Check Valve (DFCV) and Nitrogen-Enriched Air (NEA) Pipeline for LeaksPerfInsp標題操作檢查雙流量關斷活門（DFSOV），雙碟形單向活門（DFCV）和富氮管有無滲漏工作者檢查者Operational Check of Dual Flow Shut Off Valve (DFSOV), Dual Flapper Check Valve (DFCV) and Nitrogen-Enriched Air (NEA) Pipeline for Leaks操作檢查雙流量關斷活門（DFSOV），雙碟形單向活門（DFCV）和富氮管有無滲漏WARNING: MAKE SURE THAT THE SAFETY DEVICES AND THE WARNING NOTICES ARE IN POSITION BEFORE YOU START A TASK ON OR NEAR: -THE FLIGHT CONTROLS -THE FLIGHT CONTROL SURFACES -THE LANDING GEAR AND THE RELATED DOORS -COMPONENTS THAT MOVE. MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT. 警 告：在以下區域或附近工作前確認安全設備和警告牌在位： -飛控 -飛控舵面 -起落架和相關艙門 -可移動的部件 部件的移動可以使人致死致殘，也可能導致設備的損壞。WARNING: DO NOT GO INTO THE WORK AREA UNTIL A MINIMUM OF 5 MINUTES AFTER YOU REMOVE THE ACCESS PANEL. LET AIR FLOW THROUGH THE WORK AREA. AIR FROM THIS SYSTEM HAS A LOW OXYGEN CONTENT AND CAN CAUSE INJURY OR DEATH. 警 告：在拆下接近蓋板5分鐘內不要進入工作區域。讓空氣流入工作區域。此系統內的氣體氧氣含量很低，會致死致殘。WARNING: BEFORE YOU DO WORK IN A FUEL TANK, MAKE SURE THAT YOU OBEY ALL THE SAFETY PROCEDURES. THIS WILL PREVENT DEATH OR INJURY TO PERSONS AND/OR DAMAGE TO THE AIRCRAFT. 警 告：在燃油箱內工作之前，確認遵守所有安全程序。這可以防止人員傷亡以及飛機損壞。WARNING: THIS PROCEDURE USES A FUEL SYSTEM ITEM THAT IS IN A CATEGORY KNOWN AS A CRITICAL DESIGN CONFIGURATION CONTROL LIMITATION (CDCCL). CDCCL IDENTIFIES AN ITEM THAT CAN BE THE SOURCE OF A POSSIBLE FUEL TANK IGNITION. YOU MUST KEEP ALL CDCCL ITEMS IN THE APPROVED CONFIGURATION. DAMAGE, WEAR OR CHANGES TO A CDCCL ITEM CAN CAUSE A POSSIBLE FUEL TANK EXPLOSION. 警 告：此程序使用列在CDCCL內的一個燃油系統項目。CDCCL識別可能的燃油箱爆炸源。必須使所有CDCCL項目處于批準的構型。CDCCL項目的損壞，磨損和改動有可能會導致油箱爆炸。WARNING: MAKE SURE THAT: -THERE ARE NO CAPS OR COVERS ON THE FUEL TANK VENTILATION DUCTS. CAPS OR COVERS WILL CAUSE OVERPRESSURE OR UNDERPRESSURE DAMAGE TO THE FUEL TANK. -NO PERSONS ARE NEAR THE FUEL TANK OR VENTILATION DUCTS OF THE FUEL TANK. 警 告：確認： 燃油通氣管路上沒有覆蓋物；覆蓋物會導致燃油箱超壓或低壓損壞。 燃油箱或者燃油箱通氣管道附近無人。WARNING: WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A FALL CAN KILL OR INJURE YOU. 警 告：在高處工作要系好安全帶，高空墜落會造成人員傷亡。WARNING: USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL MATERIALS ONLY WITH A GOOD FLOW OF AIR THROUGH THE WORK AREA. THESE MATERIALS ARE POISONOUS AND FLAMMABLE AND SKIN IRRITANTS. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED. 警 告： 在使用溶劑/清潔劑，密封膠和其他特殊材料時,要確保工作區域通風良好。 這些材料有毒、可燃并對皮膚有刺激性。 遵守生產廠家的說明。 穿上保護性衣服 不要將他們放入嘴內。 不要吸煙。 不要吸入氣體。 如果皮膚和眼睛接觸到這些材料，馬上就醫1. Job Set-up/工作開始 T A. Aircraft Maintenance Configuration/飛機維護構型(1) You must obey the fuel safety procedures when you do work in fuel tanks (Ref. AMM TASK 28-10-00-910-801) . 在燃油箱執行工作時必須要遵守燃油安全程序(參考AMM TASK 28-10-00-910-801)。(2) Energize the aircraft electrical circuits (Ref. AMM TASK 24-42-00-861-801) . 給飛機通電(參考AMM TASK 24-42-00-861-801)B. Open, safety and tag this(these) circuit breaker(s)拔出下列跳開關并保險及貼上警告牌: PANEL/面板DESIGNATION/名稱FIN/功能項目號LOCATION/位置721VUCSAS CTRL11HHP17721VUIGGS CTRL7YAP1C. Get Access/接近(1) Put an ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position at zone 191. 在191區域下放工作梯。(2) Remove the access panel 191KB (Ref. AMM TASK 53-35-13-000-808) . 拆下接近蓋板191KB (參考AMM TASK 53-35-13-000-808)(3) If necessary, remove the cabin floor panel 251YF to get access to the top of the center fuel tank (Ref. AMM TASK 53-00-00-000-801) . 視情拆下客艙地板251YF以接近中央油箱頂部(參考AMM TASK 53-00-00-000-801)2.Procedure/步驟(Ref. Fig. Test Ports - Location SHEET 1) A. Preparation for the Test(s)/準備測試 T (1) Make sure that the DFSOV is closed. 確認DFSOV關閉NOTE: The visual indicators of the DFSOV are in the retracted position. 注 釋?zhuān)篋FSOV的目視指示器在收上位。B. Functional Test of the DFSOV, DFCV and NEA Line 功能檢查DFSOV, DFCV和NEA管路WARNING: WEAR PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE DURING THE TASK, REMOVE AND DISCARD IT. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND. 警 告：拆下或安裝保險絲時要帶護目鏡或手套。每次剪掉保險絲，取下并報廢。松動的保險絲會割傷人員或致人失明。CAUTION: BE CAREFUL WHEN YOU TOUCH THIS ASSEMBLY. IT HAS PRECISION- TOLERANCE COMPONENTS WITH VERY POLISHED SURFACES. IF YOU ARE NOT CAREFUL, IT IS VERY EASY TO CAUSE DAMAGE TO THESE COMPONENTS (INTERNAL CONTAMINATION, EXTERNAL IMPACT DAMAGE). 注 意：接觸此部件時要小心，它帶有一個公差等級很高的光亮表面，若不小心，很容易對此部件造成損傷。（內部污染，外部沖擊損傷）(1) Remove and discard the lockwire from the IGGS pallet drain port plug (plug) (4). T 拆下并報廢IGGS架排放孔塞(4)上的保險絲(2) Remove the plug (4) and the O-ring (5). T 取下孔塞 (4)和O型封圈(5)。(3) Discard the O-ring (5). T 報廢O型封圈(5)(4) Install the PRESSURE VACUUM TESTER, IGGS (98D47209001000) on the drain port. T 將PRESSURE VACUUM TESTER, IGGS (98D47209001000)安裝在排放孔上(5) Do the test. T 執行測試NOTE: For each test, stop the vacuum supply and, after two minutes, check the pressure. 注 釋?zhuān)簩?duì)于每個測試，停止真空供應并在兩分鐘后檢查壓力。(a) Supply -0.14 bar (-2.03 psi) at vacuum conditions during 5 minutes. 持續在真空狀態下供壓-0.14 bar (-2.03 psi) 5分鐘。(b) Supply -0.28 bar (-4.06 psi) at vacuum conditions during 5 minutes. 持續在真空狀態下供壓-0.28 bar (-4.06 psi) 5分鐘。(c) Supply -0.41 bar (-5.95 psi) at vacuum conditions during 5 minutes. 持續在真空狀態下供壓-0.41 bar (-5.95 psi) 5分鐘。(d) Supply -0.55 bar (-7.98 psi) at vacuum conditions during 5 minutes. 持續在真空狀態下供壓-0.55 bar (-7.98 psi) 5分鐘。(e) Supply -0.69 bar (-10.01 psi) at vacuum conditions during 5 minutes. 持續在真空狀態下供壓-0.69 bar (-10.01 psi) 5分鐘。(6) The test is satisfactory if at each step: T - there is no pressure increment, or-the pressure increment is less than 5%. 若在以上步驟中出現下列情況，則測試通過：壓力沒有增加或壓力增量小于5%(7) If the test is satisfactory: T 若測試通過：WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE MATERIAL(S). YOU MUST OBEY THE OPERATORS AND MANUFACTURERS HEALTH AND SAFETY INSTRUCTIONS. 警 告：使用耗材時要特別小心。要遵守航空公司和生產廠家的健康和安全指示。(a) Apply a thin layer of Material CML03GEE1 (Synthetic Oil base Grease-Fuel and Oxidized Environment Fluorinated -) to the new IPC-CSN (47-21-04-01-110) O-ring (5) and install it on the plug (4). 在新的O型封圈(5)IPC-CSN (47-21-04-01-110)上涂上一層CML03GEE1并安裝到孔塞(4)上。(b) Install the plug (4) on the drain port. 將孔塞(4)安裝到排放口上。(c) TORQUE the plug (4) to between 0.66 and 0.85 m.daN (58.41 and 75.22 lbf.in). 將孔塞的力矩?cái)Q到0.66-0.85 m.daN (58.41-75.22 lbf.in)之間。(d) Safety the plug (4) with Material CML14QDB1 (Wire-Locking Dia: 0.5 mm (0.020 inch) CRES Nickel Alloy -) with the double lockwiring method (Ref. AMM TASK 20-11-11-911-803) . 使用CML14QDB1將孔塞(4)打上雙保險(參考AMM TASK 20-11-11-911-803)(e) Do the Close-up procedure. 執行結束工作程序。(8) If the test is not satisfactory do the Leak Test of the NEA Line given in the subsequent T Para. C. 若測試不通過，執行步驟C對NEA管路進行滲漏測試。CAUTION: DO NOT LET PAINT PARTICLES GO INTO THE FUEL TANK. REMOVE THE PARTICLES WITH A VACUUM CLEANER (IF YOU CANNOT USE A VACUUM CLEANER, USE AN AIR BLOWER). 注 意：不要讓油漆顆粒進入油箱。用真空吸塵器清除顆粒（若無真空吸塵器，使用鼓風機）C. Leak Test of the NEA Line/NEA管路滲漏檢查NOTE: Two persons are necessary to do this subtask. 注 釋?zhuān)盒枰獌扇藖?lái)執行此工作(1) Apply WATER - SOAPY SOLUTION on the couplings and connections of the NEA Line. T 在NEA管路的耦合器和接頭處涂上肥皂水。(2) Supply 0.69 bar (10.01 psi) at pressure conditions. T 供壓0.69 bar (10.01 psi) (3) After two minutes, do a visual check of the joints and couplings for signs of leaks. T 兩分鐘后，目視檢查耦合器和接頭有無滲漏痕跡NOTE: Bubbles are an indication of leaks. 注 釋?zhuān)嚎梢酝ㄟ^(guò)氣泡來判斷是否滲漏。(4) If there are leaks:/若存在滲漏 T (a) Replace the defective connections and/or NEA line (Ref. AMM TASK 47-20-50-000-801)and (Ref. AMM TASK 47-20-50-400-801) . 更換有缺陷的接頭和/或NEA管路。 (參考AMM TASK 47-20-50-000-801)和(參考AMM TASK 47-20-50-400-801)(b) Do again the Functional Test of the DFSOV, DFCV and NEA Line given in Para. B. 再次執行B步驟對DFSOV, DFCV和NEA Line的功能測試(5) If there are no leaks do the Test of the DFSOV given in the subsequent Para. D. T 若無滲漏，執行D步驟的DFSOV測試D. Test of the DFSOV/DFSOV測試WARNING: WEAR PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LO