電動葫蘆出廠檢驗報告1

1、 鋼 絲 繩 電 動 葫 蘆 檢 測 報 告Test report of wire-rope electric hoistJB/T9008.12004JB/T9008.22004規格型號 CDA210t-18m specification and type出廠編號11067703 Manufacturing Code工作級別 M3 work grade檢驗日期 2011年06月 inspection date河南省中原圣起起重機械有限公司Henan province shengqi Crane Co.,Ltd鋼絲繩電動葫蘆檢驗記錄Test record of wire-rope electri

2、c hoist序號No.考核項目Inspected item單位unit質量指標Quality standard檢驗結果Test result結論conclusion備注remark1靜載試驗Static testt試驗載荷test load:1.25Gn符合要求合格2動載試驗Dynamic testt試驗載荷test load:1.1Gn符合要求合格3降壓試驗Reduced pressure experiment90%額定電壓試驗載荷1.0Gn 90% rated voltage test load 1.0Gn(Gn為額定載荷Gn is rated load)符合要求合格4起升速度Lifti

3、ng speedm/min偏差為名義值的10%Warp is 10% of normal value.6.9m/min合格5起升高度Lifting heightm偏差為名義值的-3%Warp is -3% of normal value.17.92m合格6制動下滑量Brake slide quantitymm試驗載荷test load 1.0G制動下滑量brake slide quantity SV/100(V為1分鐘內實測吊鉤穩定上升的距離V is tested hook hoisting distance in one minute)16mm合格7起升機構噪音Noise of liftin

4、g mechanismdB(A)試驗載荷1.0Gn時(when test load is 1.0Gn)0.25t5t85,5t以上9072合格8電動小車空載噪音zero load noise of electric trolleydB(A)8071合格9電動小車爬坡試驗climbing test of electric trolley坡度不小于1/200 gradient not less than 1/200試驗載荷test load:1.0Gn符合要求合格10運行速度Traveling speedm/min偏差為名義值的15%Warp is 15% of normal value. 11導

5、繩器Rope-guide裝配合理,空鉤下降時,鋼絲繩應能自由地從導繩器的出口排出.Reasonable assembly, when hook without load descends, wire rope should be put out freely from the rope-guide.能自由排出合格12限位器limiter限位開關動作可靠Limit switch should act reliably.可靠合格13鋼絲繩Wire rope有合格證且繩端固定牢靠,編繞正確. Having certificate of approval and rope end is fixed r

6、eliably.正確合格14防護等級Protection gradeIP44IP44合格鋼絲繩電動葫蘆檢驗記錄Test record of wire-rope electric hoist15絕緣電阻Insulation resistorM1.5480合格16接地電阻Earth resitor0.10.01合格17起升減速器內雜物sundries in hoisting reducermg250191合格18油漆漆膜厚度Paint film thicknessm油漆漆膜總厚度不小于50 general thickness of paint film is no less than 50(取10

7、處平均值get mean value from ten places value)54合格19漆膜附著力Adhesion of paint film應符合GB9286的規定Accord with the regulations of GB9286符合規定合格20升壓試驗Lifting pressure test110%Ue.1.0Gn載荷,電動機和電器裝置無異常When 110%Ue.1.0Gn load, there is no abnormal phenomenon with the motor and electric appliance.無異常合格21起升機構用減速器的箱體蓋中心距偏差

8、center distance warp of body cover of reducer in lifting mechanism mm0.09-0.02合格22鉤口變形Mouth of hook distortion%鉤口變形量不大于0.25%Deflection quantity of hook mouth is not more than 0.25%.0.02%合格23電氣設備Electric equipment檢查是否有合格證和質檢中心型式報告.Check if there is any certificate of approval and quality inspection report.有合格檢驗結論test conclusion:經檢驗各項指標符合標準要求經檢驗各項指標符合JB/T9008.12004、JB/T