空調機組控制箱操作說明中英對照

1、空調機組控制箱操作說明Operating Instructions for Control Cabinet of Air Conditioning Unit根據貴方所提要求，控制柜設制冷機手動啟停按鈕；1#空調、電加熱、風閥手動啟停按鈕；2#空調、電加熱、風閥手動啟停按鈕；1#空調機組手動/自動轉換開關；制冷停止/自動轉換開關；制制熱停止/自動轉換開關；通風停止/自動轉換開關；自動啟動、停止按鈕。In accordance with requirements proposed by your party, the control cabinet is equipped as follows:

2、manual“ ON/OFF” button of the refrigerator; 1# air conditioner, electric heating, manual “ON/OFF” button of the air damper; manual/ automatic switch of 2# air conditioner, electric heating, manual “ON/OFF” button of the air damper; 1# air conditioning unit; refrigeration/stop /automatic switch; heat

3、ing/ stop /automatic switch; ventilation /stop /automatic switch; automatic ON/ OFF button. 機組所具備的功能：1、空調機組設手動/自動轉換開關，手動時由控制柜面板啟停按鈕啟動相應的設備。2、 面板設有制冷、制熱、 通風轉換開關，控制箱處于制冷狀態時開啟水泵、制冷機、空調機組；當處于制熱狀態時開啟電加熱、空調機組；當處于通風狀態時開啟空調機組。面板上設自動啟動、停止按鈕，在制冷、制熱、通風任一狀態下自動啟動、停止按鈕有效，空調機組處于手動狀態時，自動按鈕無效；3、消防信號、防火閥信號關閉機組。4、 1#/

4、2#空調機組只要有一臺處于自動狀態時，制冷、制熱、通風轉換開關有效，1#/2#空調機組都處于手動時制冷、制熱、通風轉換開關無效。5、 制熱狀態時根據回風溫度控制電加熱啟停，電加熱與風機連鎖，風機不啟動， 電加熱不啟動；風機電加熱段設高溫報警傳感器，當電加熱段內溫度超過75°（參數可調）時，自動切斷電加熱。6、制冷狀態時，先啟動空調機組，再啟動水泵，最后啟動制冷機組；本控制只提供制冷機啟停干接點信號。制冷狀態因空調機組無電動水閥，故無法實現溫度制動控制；7、通風狀態啟動風機。Functions of the unit:1. The air conditioning unit is eq

5、uipped with the manual/ automatic switch. The corresponding equipment is started with the ON/ OFF button on the panel of the control cabinet for manual operation.2. The panel is equipped with a switch for refrigeration, heating and ventilation. The control cabinet is used to start the water pump, re

6、frigerator and air conditioning unit in refrigeration state; start electric heating and air conditioning unit in heating state; start the air conditioning unit in ventilation state. There are automatic start and stop button on the panel which are effective in any one of the states including refriger

7、ation, heating and ventilation. The automatic button is invalid when the air conditioning unit in the manual state;3. Signal of fire fighting and fire damper can shut down the unit.4. The switch for refrigeration, heating and ventilation is valid when either set of 1#/ 2# air conditioning units is i

8、n automatic state; When all 1#/ 2#air conditioning units are in manual state, the switch for refrigeration, heating and ventilation is invalid.5. In heating state, ON/OFF of the electric heating is controlled by the temperature of the return air with the electric heating and air blower interlocked,

9、air blower and electric heating not started; High-temperature alarm sensor is set for the electric heating section of the air blower. When the temperature in the electric heating section exceeds 75° (the parameters are adjustable), the electric heating is disconnected automatically.6. In refrig

10、eration state, the air conditioning unit is started first, then the water pump and the refrigerator unit at last; The control only provides the dry contact signal for ON/OFF of the refrigerator. In refrigeration state, the temperature brake control cant be realized for there is no electric water val

11、ve for the air conditioning unit;7. In ventilation state, the air blower is started.控制柜具體操作規程：1、將1#、 2#空調機組轉換開關旋至手動狀態；制冷、制熱、通風轉換開關旋至停止狀態，此時機組處于手動狀態，在此狀態下按控制柜面板上相應的啟動按鈕， 其對應的控制系統開始工作，按下停止按鈕后其對應的控制系統停止工作。2、將1#或 2#空調機組任一臺轉換開關旋至自動狀態；將制冷轉換開關旋至自動狀態，制熱、通風轉換開關在停止位置；此時為制冷自動狀態。在此狀態下按自動啟動按鈕，機組按制冷狀態自動執行順序啟動程序，具

12、體順序如下：當1#空調機組處于自動狀態時：開啟1#空調機組送風機-開啟循環水泵-開啟制冷機組。當2#空調機組處于自動狀態時：開啟2#空調機組送風機-開啟循環水泵 -開啟制冷機組。3、將1#或 2#空調機組任一臺轉換開關旋至自動狀態；將制熱轉換開關旋至自動狀態，制冷、通風轉換開關在停止位置；此時為制熱自動狀態。在此狀態下按自動啟動按鈕，機組按制熱狀態自動執行順序啟動程序，具體順序如下：當1#空調機組處于自動狀態時：開啟1#空調機組送風機-開啟1#空調機組電加熱。當2#空調機組處于自動狀態時：開啟2#空調機組送風機-開啟2#空調機組電加熱。 電加熱根據回風溫度與回風溫度設定值自動啟停；空調機組設有

13、高溫報警傳感器， 當高溫報警傳感器所測得的空調機箱溫度超過高溫報警設定值時，自動切斷空調機組電加熱，溫度降低后自動恢復。4、將1#或2#空調機組任一臺轉換開關旋至自動狀態；將通風轉換開關旋至自動狀態，制冷、制熱轉換開關在停止位置；此時為通風自動狀態。在此狀態下按自動啟動按鈕，機組按通風狀態自動執行順序啟動程序，具體順序如下：當1#空調機組處于自動狀態時：開啟1#空調機組送風機。當2#空調機組處于自動狀態時：開啟2#空調機組送風機。5、根據貴方要求，空調機組風閥設為手動啟停，當需要開啟風閥時，按相應啟動按鈕，風閥即可開啟；同理關閉時按相應停止按鈕。Detail operating instruc

14、tions of the control cabinet:1. Turn the switches of 1# and 2# air conditioning units to the manual state; the switch for refrigeration, heating and ventilation to the stop state with the unit in the manual state. In such state, pressing the start button on the panel of the control cabinet will star

15、t the corresponding control system and pressing the stop button will stop the corresponding control system.2. Turn the switch of either 1# or 2# air conditioning unit in the automatic state; turn the refrigeration switch to automatic state and heating and ventilation switch to stop position; it is a

16、utomatic refrigeration state now. In this state, after pressing the automatic start button, the unit will carry out the sequential start program as per refrigeration state automatically detailed as follows: When 1# air conditioning unit is in automatic state: start the new air damper of 1# air condi

17、tioning unit-start air feeder of 1# air conditioning unit -start circulating water pump-start refrigerator unit. When 2# air conditioning unit is in automatic state: start new air damper of 2# air conditioning unit -start air feeder of 2# air conditioning unit -start circulating water pump-start ref

18、rigerator unit.3. Turn the switch of either 1# or 2# air conditioning unit to automatic state; Turn the heating switch to automatic state, the switch of refrigeration and ventilation to stop position; it is automatic heating state now. In this state, after pressing the automatic start button, the un

19、it will carry out the sequential start program as per heating state automatically detailed as follows: When 1# air conditioning unit is in automatic state: start the new air damper of 1# air conditioning unit -start air feeder of 1#air conditioning unit -start electric heating of 1# air conditioning

20、 unit. When 2# air conditioning unit is in automatic state: start the new air damper of 2# air conditioning unit -start the air feeder of 2#air conditioning unit -start electric heating of 2# air conditioning unit. ON/OFF of the electric heating is realized according to the temperature of the return

21、 air and the set value of it; High-temperature alarm sensor is set to the air conditioning unit. When the case temperature of the air conditioner measured by the high-temperature alarm sensor exceeds the set value for high-temperature alarm, the electric heating of the air conditioning unit will be

22、disconnected automatically and recovered automatically after the temperature is reduced.4. Turn the switch of either 1# or 2# air conditioning units to automatic state; Turn the switch of ventilation to automatic state, the switch of refrigeration and heating to stop position; it is automatic ventil

23、ation state now. In this state, after pressing the automatic start button, the unit will carry out the sequential start program as per ventilation state automatically detailed as follows: when 1# air conditioning unit is in automatic state: start the new air damper of 1# air conditioning unit -start

24、 the air feeder of 1# air conditioning unit. When 2# air conditioning unit is in automatic state: start the new air damper of 2# air conditioning unit -start the air feeder of 2# air conditioning unit.TD400 面板實際效果圖及操作說明空調機組控制柜開機送電以后，TD400 文本顯示器顯示如下開機畫面：Actual working sketch and operating instruction

25、s for TD400 panelAfter starting and powering on the control cabinet of the air conditioning unit, TD400 text panel displays the following startup picture:Automatic control systemWorking condition Unit state:Automatic control system of the air conditioning unitWorking condition:Unit state:此畫面為開機顯示畫面，

26、當系統處于手動狀態時，此畫面上的工作狀態后 面的黑框內將出現 手動字樣反之為自動。當制冷、制熱、通風轉換開關任有一個 在自動狀態時，機組狀態后面的黑框內將出現對應的制冷、制熱、通風字樣；若制冷、制熱、通風轉換開關都處于停止狀態時，無顯示。在開機畫面狀態下按TD400面板上的鍵，將進入下一畫面：This picture is the startup picture. When the system is in manual state, the word Manual will be shown in the black box behind the working condition in t

27、he picture. Otherwise, the word Automatic will be shown. When any switch for refrigeration, heating and ventilation is in automatic state, the corresponding word Refrigeration, Heating and Ventilation will be shown in the black box behind the unit state; If all switches for refrigeration, heating an

28、d ventilation are in stop state, there is no display.By pressing the key ” on TD400 panel in startup picture, the next picture is accessible:1- Air conditionerAir temperatureCase temperatureValue display of 1# air conditionerAir channel temperature:Case temperature:此畫面為1#空調機組數值顯示畫面，此畫面顯示1#空調機組風道溫度與機

29、 箱溫度，此數值只能顯示，不能設定。在此畫面狀態下按TD400面板上的鍵，將進入下一畫面：This picture is that for value display of 1# air conditioning unit. The picture shows the air channel and case temperature of 1# air conditioning unit. The value can only be displayed andcan' be set.By pressing the key ” on TD400 panel in the picture,

30、 the next picture is accessible:1/空調髓設定 溫度設定：hlue setting of 1?Temperature setting High-temperatueValue setting of 1# air conditionerTemperature setting:High-temperature setting:此畫面為1#空調機組數值設定畫面，此畫面顯示1#空調機組風道溫度與機 箱溫度設定值，機箱溫度與高溫設定相比較，當機箱溫度大于高溫設定值時，自 動切斷電加熱以防止高溫燒壞空調機箱。風道溫度與溫度設定相比較控制電加熱的啟停，以保持室內溫度的恒定。具

31、體設定如下：按TD400操作面板右側“ ENTER”鍵，溫度設定后面黑框 開始出現閃爍，按鍵增加數值，按鍵減少數值；當達到合適數值后 按“ENTER”鍵確認；此時高溫設定黑框開始閃爍，按鍵增加數值，按 鍵減少數值；當達到合適數值后按“ ENTER”鍵確認。此界面設定完成。在此畫面狀態下按TD400面板上的鍵，將進入下一畫面：This picture is that for value setting of 1# air conditioning unit. The picture shows the set value of the air channel temperature and th

32、e case temperature for 1# air conditioning unit. By comparing the case temperature with the high-temperature setting, when the case temperature is larger than the high-temperature setting value, the electric heating shall be disconnected automatically to avoid burning the case of the air conditioner

33、 due to high temperature. ON/OFF of the electric heating shall be controlled by comparing the air channel temperature with the temperature setting to keep constant room temperature.The detail settings are as follows: after pressing the key ENTER“ in the right of TD400 operating panel, the black box

34、behind the temperature setting begins to flick. The value can be increased by pressing the key A" and decreased by pressing the key "； When the applicable value is reached, press the key ENTER" to confirm; Now, the high-temperature setting black box begins to flick. The value can be i

35、ncreased by pressing the key T and decreased by pressing the key ”； When the applicable value is reached, press the key ENTER“ to confirm. The interface setting is finished.By pressing the key ” on TD400 panel in the picture, the next picture is accessible:It Air conditionerAir temperature Case temp

36、eratureValue display of 2# air conditionerAir channel temperature:Case temperature:此畫面為2#空調機組數值顯示畫面，此畫面顯示2#空調機組風道溫度與機 箱溫度，此數值只能顯示，不能設定。在此畫面狀態下按TD400面板上的鍵，將進入下一畫面：This picture is that for value display of 2# air conditioning unit. The picture shows the air channel temperature and case temperature of

37、2# air conditioning unit. The value can only be displayed but not set.By pressing the key ” on TD400 panel in the picture, the next picture is accessible:Value setting of 舞Temperature setting High-temperatureTemperaturesetting of 2# air conditionerTemperature setting:High-temperature setting:此畫面為2#空

38、調機組數值設定畫面，此畫面顯示2#空調機組風道溫度與機 箱溫度設定值，機箱溫度與高溫設定相比較，當機箱溫度大于高溫設定值時，自 動切斷電加熱以防止高溫燒壞空調機箱。 風道溫度與溫度設定相比較控制電加熱 的啟停，以保持室內溫度的恒定。具體設定如下：按TD400操作面板右側“ ENTER”鍵，溫度設定后面黑框 開始出現閃爍，按鍵增加數值，按鍵減少數值；當達到合適數值后 按“ENTER”鍵確認；此時高溫設定黑框開始閃爍，按鍵增加數值，按 鍵減少數值；當達到合適數值后按“ ENTER”鍵確認。此界面設定完成。在以上任一畫面狀態下按“ ESC”鍵，此時畫面顯示：數值顯示與設定設備狀態在此畫面按鍵至設備狀

39、態，按“ ENTER”鍵確認后進入畫面：This picture is that for value setting of 2#air conditioning unit. The pictureshows the set value of the air channel temperature and case temperature for 2# air conditioning unit. By comparing the case temperature with the high-temperature setting, when the case temperature is hi

40、gher than the high-temperature setting value, the electric heating shall be disconnected automatically to avoid burning the case of the air conditioner due to high temperature. ON/ OFF of the electric heating shall be controlled by comparing the air channel temperature with the temperature setting t

41、o keep the constant room temperature.The detail settings are as follows: after pressing the key ENTER“ in the right of TD400 operating panel, the black box behind the temperature setting begins to flick. The value can be increased by pressing the key A" and decreased by pressing the key "；

42、 When the applicable value is reached, press the key ENTER" to confirm; Now, the high-temperature setting black box begins to flick. The value can be increased by pressing the key T and decreased by pressing the key ”； When the applicable value is reached, press the key ENTER“ to confirm. The i

43、nterface setting is finished.By pressing the key ESC" in any picture state above, the picture will shows: Value display and setting Equipment state1?機組設備狀態 機組運行狀態：機組故障狀前Press the key ” in the picture to access the equipment state and access the picture after confirmation by pressing the key ENT

44、ER”：Kiln it device stateRunning stateFault state1#unit device stateRunning state of the unit:Fault state of the unit:此畫面為1#機組運行、故障狀態顯示，機組運行時機組運行狀態顯示“運 行”反之顯示“停止”；機組故障狀態正常時顯示：“正?！保敊C組電機出現故 障時顯示“故障”。在此畫面狀態下按TD400面板上的鍵，將進入下一畫面：This picture shows the running and fault state of 1# unit. When the unit run

45、s, the running state of the unit shows Running" and Stop" on the contrary; When the fault state of the unit is normal, it shows: Normal“ and when the unit motor goes wrong, it shows Fault”.By pressing the key ” on TD400 panel in the picture, the next picture is accessible:1#機組設備狀態 電加熱狀梯新風閥

46、狀態：State Of 11 unit deviceEketric heatingNew air damperState of 1# unit deviceElectric heating state:New air damper state:此畫面為電加熱、新風閥狀態顯示，電加熱運行時電加熱狀態顯示“運行”反之顯示“停止”；新風閥運行時新風閥狀態顯示“開”反之顯示“關”。在此畫面狀態下按TD400面板上的鍵，將進入下一畫面：This picture shows the state of the electric heating and new air damper. When the ele

47、ctric heating runs, the electric heating state showsRunning“ and Stop“ on the contrary; When the new air damper runs, the new air damper state shows On” and Off“ on the contrary.By pressing the key ” on TD400 panel in the picture, the next picture is accessible:H機組設備狀態 機組運行狀態：機組故障狀態：2# Unit device s

48、tateRunning stateFault stateState of 2# unit deviceRunning state of the unit:Fault state of the unit:此畫面為2#a組運行、故障狀態顯示，機組運行時機組運行狀態顯示“運 行”反之顯示“停止”；機組故障狀態正常時顯示：“正?！?，當機組電機出現故 障時顯示“故障”。在此畫面狀態下按TD400面板上的鍵，將進入下一畫面：This picture shows the running and fault state of 2# unit. When the unit runs, the running s

49、tate of the unit shows Running" and Stop" on the contrary; When the fault state of the unit is normal, it shows: Normal“ and when the unit motor goes wrong, it shows Fault”.By pressing the key ” on TD400 panel in the picture, the next picture is accessible:State of 2? unit deviceElectric heating 卜那 air damperState of 2# unit deviceElectric heating state:New air damper state:此畫面為電加熱、新風閥狀態顯示，電加熱運行時電加熱狀態顯示“運行”反之顯示“停止”；新風閥運行時新風閥狀態顯示“開”反之顯示“關”。在此畫面狀態下按TD400面板上的鍵，將進入下一畫面：This picture shows electric heating and new air damper state. When the electric heating runs,