VIVADO下ILA使用規范指南規范.doc

1、VIVADO 下ILA 使用指南ILA是VIVADO下的一個DEBUG- IP ,類似于片上邏輯分析儀，通過在 RTL設計 中嵌入ILA核，可以抓取信號的實時波形，幫助我們定位問題。本文檔以一個簡單的 COUNTER設計為例，對VIVADO (2014.1)下ILA核的使用進行說明。第一部分RTL設計module counter(input clk, output 3:0 q );wire clk;/想抓取cnt信號進行觀察(* keep = TRUE *)reg 3:0 cnt = 4d0;assign q = cnt;always(posedge clk) begincnt . . 0 )

2、Hc t 1. -ori-a Mw -t e.bi tn ，上垂4=國+ i v* 廣具乂 IBTLIlhl3r 電 f PTQteuJj-Cl. - 1024 3opl4 fate. LepTtlJ?？诙?L TirliuB-eir Out PortB- Th J. BBCfr J n P-nrtI r-u t Ff七國=| O二I -r lEiB-aHiT Ae-i 工皆t-1: 1 rLg f- Cspt ut e Sent jr-1.F- JtL ElkitLrX-匚 J 1 .UX1后 丁卜e . FnnileT 口才亭hy-： ch : 西 看 :rcTs r-H1 lw ：be

3、r o t ton g176 t mrs 11在“component Name ”可以修改例化名,在“Number of Prober ”可以修改想抓取信號 的分組個數，在本例中僅觀察1組信號cnt,在“sample Data Depth ”可以修改抓取信 號的深度，本例選擇默認值1024。其他選項保持默認值。第二頁input clk, output 3:0 q );wire clk;/想抓取cnt信號進行觀察(* keep = TRUE *)reg 3:0 cnt = 4d0;assign q = cnt;always(posedge clk) begincnt Then c&nfisure

4、 the host naiie and settlnRB. Use Local ervex if the t arnct 1 s attached to the local Jiadnlne:Gonn百石十 to; |1 s-erver i ii ”R H m - h I i Click Next to 1 aunch and/or connect 弋o the vcsc_servcr (p*rt 60001 and Invserver (port 3121) &pplicat 1 ons on tine local m也uhinu+ 口aek J Nsxt 3；| 二it二L-上 匚。門。5

5、I |點擊Next點擊Next點擊Finish點擊ok，該錯誤是軟件誤報發現vivado界面的左下角的Program Device選項變亮，點擊該選項，下載 bit文件ProgTaw and Debug Bi.tstrean Settings士 Generate Bilstrean,留 Hardware Manager0 Open Target Pro gran工/ Add Canfiguration Me工 Program DeviceSelect a bitstream prog3:ajiming file and download it to your hardware device.

6、Yoli can optionally select a debug probes file that corresponds to the debug cores contained in the bitstream prcgramMing file.Bitstreat file: |E:/TEST/debug_test_14_l/test. runs/test. blt| - Debua Probes file: IE:/TEST/debug_test_14_l/test. runs/inpl_l/debug_nets. Its -Pro,., Cancel點擊Pro.開始下載下載完成，v

7、ivado界面發生變化打開window菜單欄，選擇 Debug Probes選項，界面會多出一個 Debug Probes窗口將需要觀察的信號cnt信號“拖入”右側的Basic Trigger Setup窗口在這個界面中可以修改觸發條件（cnt=2）,觸發深度（1024）,觸發位置（500）等參數（類似于 chipscope ）ILA Prayer Uvslode 5eftinsi=CaptureHod* SettingsTrigfer Capture StitmA 口上Cere status;Idlti尸re-TiqehWaiitiih% f-r Trigger iVirvisw 1 Qf 1VLndtiv sarafde 0 of 1024 Total suple *0 匚，iri + 】b* C t 3S tl IC - .- - - .S r11Tl. 二jlIjJCapturenoidc:luiber M nind”1B3.3 ic t ri E.ger Selqp X X1 - JIInJow J3ta dtptti:.rlfigev p&slticn in TliHkv: 1