基于單片機的電阻、電容、電感測試儀

1、基于單片機的電阻、電容、電感測試儀_畢業論文摘 要隨著電子工業的發展，電子元器件急劇增加，電子元器件的適用范圍也逐漸廣泛起來，在應用中我們常常要測定電阻，電容，電感的大小。因此，設計可靠，安全，便捷的電阻，電容，電感測試儀具有極大的現實必要性。在系統硬件設計中，以MCS-51單片機為核心的電阻、電容、電感測試儀，將電阻，電容，電感，使用對應的振蕩電路轉化為頻率實現各個參數的測量。其中電阻和電容是采用555多諧振蕩電路產生的，而電感則是根據電容三點式產生的，將振蕩頻率送入AT89C52的計數端端，通過定時并且計數可以計算出被測頻率，再通過該頻率計算出被測參數。在系統的軟件設計是以Keil51為仿

2、真平臺，使用C語言與匯編語言混合編程編寫了系統應用軟件；包括主程序模塊、顯示模塊、電阻測試模塊、電容測試模塊和電感測試模塊。最后，實際制作了一臺樣機，在實驗室里進行了測試，結果表明該樣機的功能和指標得到了設計要求。關鍵詞：?jiǎn)纹瑱C(jī)，555多諧振蕩電路，LED動態顯示模塊，電容三點式振蕩I I你好IIABSTRACTABSTRACTWith the development of electronic industry，electronic components rapidly increased the scope of electronic components widely up gradua

3、lly，in applications we often measured resistors，capacitors，inductors size. Therefore,the design of reliable，safe，convenient resistance，capacitance，inductance tester of great practical necessity.In the system hardware design，take the MCS-51 monolithic integrated circuit as the core resistance，the ele

4、ctric capacity，the inductance reflectoscope reflector，the resistance，the electric capacity，the inductance，the use correspondence's oscillating circuit transforms for the frequency realizes each parameter survey.And the resistance and the electric capacity are use 555 multiresonant circuits to pr

5、oduce，but the inductance is produces according to the electric capacity bikini，the oscilation frequency will send AT89C52 the counting to be neat，through and fixed time counts may calculate by the frequency measurement rate，figures out again through this frequency meter is measured the parameter.In

6、system's software design is take Keil51 as the simulation platform，used the C language and the assembly language mix programming has compiled the system application software；including master routine module，display module，resistance test module，electric capacity test module and inductance test mo

7、dule.Finally，the actual production of a prototype，tested in the laboratory results show that the prototype of the functions and indicators are the design requirements.KEY WORDS: Single slice of machine，555 resonance swings circuit，LED dynamic display module，Capacitance three-point shockIII III你好IV目

8、錄目 錄1 前言 . 11.1 設計的背景及意義 . 11.2 電阻、電容、電感測試儀的發展歷史及研究現狀 . 11.3 本設計所做的工作 . 31.4 本論文的結構安排 . 32 電阻、電容、電感測試儀的系統設計 . 52.1 電阻、電容、電感測試儀設計方案比較 . 52.2 系統的原理框圖 . 53 電阻、電容、電感測試儀的系統硬件設計 . 73.1 MCS-51單片機電路的設計 . 73.2 LED數碼管電路與鍵盤電路的設計 . 93.3 測量電阻、電容電路的設計 . 133.4 測量電感電路的設計及仿真 . 173.5 多路選擇開關電路的設計 . 204 電阻、電容、電感測試儀的軟件設計 . 224.1 I/O口的分配 . 224.2