機械外文文獻

1、The Design of the Welding Junetion Clamp of MotorcarAbstractThe text introduces the design method and construction of the welding junction clamp of motorcar.KeyWords: Weldingassembly Base Clamp Loeation1. IntroductionAssembly and welding fixture in the automotive body assembly and welding production

2、 line of critical process equipment related to manufacturing quality of the car. In welding production.Assembly and welding fixtures in addition to the completion of this process the parts assembly,positioning, the also served as a test and calibration procedures on the Road, welding partswelding qu

3、ality of the task, so its design and manufacture of the welding process affects the level of automobile production capacity and product quality.Automotive style vary, welding fixture shape and thus vary widely, but in the design, manufacture, adjustments have in common,you can learn from each other.

4、2. the structural design of welding fixtureFixture structural design, to ensure that the folder has a good convenience of operation, clamping positioning reliability. Fixture manufacturers also adjusted to ensure easy integration of various parts of the structure surface should allow sufficient room

5、 for adjustment to ensure the three-dimensional adjustable. Ensuring the accuracy of the welding quality and welding under the premise of the structure of fixture should be as simple as possible. Fixture design is usually the general use of welded structures, the basic componentis divided into three

6、 parts, namely base, support the positioning part, clamping parts, for each specific fixture positioning support base and some of the general use of 10 to 20 mm thick steel plate welded structure A3.Clamping part of the normal 10 mmwith a thickness of about 45 combination of welded steel plate. Pneu

7、matic and manual clamping part of the two, according to the size of car production clamping method to determine the general high-volume pneumatic clamping, then manually clamping can be used as auxiliary clamping; small quantities in order to reduce the cost of manually clamp mode. Manual clamping i

8、s usually manually fast clip, manual quick clip of their products has becomethe standard, type and quantity needed can be purchased in the market. For somefixtures require apneumatic clamping, but direct use of pneumatic clamping. May damage the workpiece, then, can be manually pressed first place,

9、to give a pneumatic clamping force to clamp the workpiece, which is manual - Pneumatic J the fixture clamping system is installed on a large platform, all guaranteed fixture in the welding position of welding conditions should be consistent with the design of the workpiece coordinate dimensions, whi

10、ch involves the positioning fixture benchmarks.3 assembly and welding fixtures benchmarks and their choice of support surface3.1 t flip-chip benchmark test fixtureEachfixture must be a fixture coordinate system, in this coordinate system, the coordinates of its base of support size should be support

11、ing the workpiece and the coordinates corresponding to the samesize. Fixture coordinate system is established based on fixture side of the child base.Becausethe whole fixture system to guarantee a space auto welding pieces of three-dimensional coordinate system, so this system in all of the fixture

12、must have a common benchmark, this benchmark is the fixture to install platform that is the X, Y Zuo Biao, each specific fixture in platform location, the corresponding height shall coordinate Z, so that three-dimensional XYZcoordinate system is established. In order to facilitate the installation a

13、nd measurement fixture, install the platform must have the coordinates of reference, there are generally three types of structure below:3.1.1 The quasi-hole method TombInstallation of platform design is the four reference holes, each hole in the center of the two connection lines form a coordinate d

14、irection, the four holes constitute the coordinates of two perpendicular lines. This, XY plane coordinate system on the set. The establishment of this benchmark is relatively simple, easy to process, but the measurements used in conjunction with the base block. Base block is a rectangular block size

15、 of the amount of accurate measurement, the platform is installed into the base hole in the base marketing, reference block off a side close to the two benchmarks to form a coordinate direction.3.1.2 V-type to be lawThis approach is in the process to install the platform into each of two 90-degree V

16、-groove, which V-groove of a plane surface perpendicular to the installation of platform, such plane perpendicular to the platform, the two V-groove groove the surface of the form XY plane coordinate system.3.13 reference block methodReference block using the side perpendicular to the two constituti

17、ve three-dimensional XYZ coordinate system, usually a fixture base with 3 to 4 blocks can be directly installed on theplatform can also add a bearing fixed to the fixture platform, but requires reference block The last plane to control the height must be consistent with the direction. Manufacturing

18、base to adjust the block in front of the two methods is relatively difficult, but the measurement is convenient, especially the use of CMM measurements. Block method with a benchmark of installation platform plane processing requirements are relatively low, a larger size of the installation platform

19、 should use this method.3.2 The choice of bearing surfaceBearing surface should be used whenwelding pieces are fixed on the surface of the cut plane to plane and install the platform angle is not greater than 15 degrees on the surface. As far as possible the detection surface and welding pieces of t

20、he same, flat surface as far as possible in order tofacilitate processing and adjustment . Structure should be designed bearing surface can be easily processed, with the numberof modules for the product can be used to process bearing NC surface, in the design, the car coordinate Xi point was not nec

21、essarily suited fixture bearing surface with NC, which requires supporting the fixture block access point S as the base, the establishment of a digital surface, this surface should be consistent and be the Bearing surface, so that whenit was manufactured to S base point for NC machining, precision m

22、achining and assembly debugging easy.4. positioning the workpieceThe general location of the workpieces to holes or obvious surface features as the positioning reference surface. The positioning pins are commonly used components. Fixture positioning sub-activities, and fixed positioning of two, for

23、some jobs, in order to facilitate the workpiece into and out, positioning the form of optional activities, events or block pin positioning structure of the form sub-pneumatic and manual, in principle, put the workpiece seeded, positioning pieces to open into the workpiece, the positioning pieces out

24、, and then clamp; workpiece removed, the position to return items before and after clamp release. Activities can be used locate pieces of the movement structure of pan-type or flip-style, pan-type structure is usually given priority. 5 welding pieces of the station transfer betweenMost auto welding

25、parts to be welded in several station, so it needs transmission device, usually to avoid interference welding fixture, the workpiece in the transmission before the first piece rises, which requires use elevator, lifting bodies Gear rack, four-link, etc., rack and pinion drive structure processing and link structure are not a