測距儀使用說明

1、Forestry pro measurement procedure guideTo start 開始press POWER button to turn on 按電源鍵 POWER 打開confirm your mode with the internal display (default is “l(fā)ast used” setting) 確認你 的模式與內部顯示(默認是“最后的使用設置)3,Set your desired mode and start measuring 設置你想要的模式，開始測量Mode setting :模式設置Target priority modes 目標優先模式1

2、、press and hold MODE button,then press and hold POWER button within 0.5 second,按下并保持住模式按鈕，然后同時按住電源按鈕在0.5秒之內2、Continue to press and hold both buttons(more than 2 seconds)until first target priority mode and distant target priority mode are switched. 繼續同時按住兩個按 鈕(超過2秒)，直到第一個目標優先模式和遙遠的目標優先模式切換。3、if the

3、button is not pressed within 0.5 second ,the display unitwill be switched.如果按鈕不是壓在0.5秒之內，顯示單元米/碼/英尺。將切換。Dst:Distant priority mode (factory setting)遙遠的優先模式(工廠設置)1st:first priority mode 第一優先模式Measurement modes 測量模式Press and release MODE button,按下和釋放模式按鈕Measurement mode changes in the order of 1 ( Act)

4、to 6 (Hor)as shown below.測量 模式變化的順序1(Act)到6(Hor)如下所示。Holding down MODE button longer switches the display unit.按住模式 MODE 按鈕 開關的顯示裝置Act:linear distance 直線距離Hor(solid):horizontal distance 水平距離Hgt(solid):height from horizontal 高度Ang: angle (degrees)from horizontal 角度Hgt(blinking):vertical separation(he

5、ight between two points) Hgt 閃動為垂直分離 (兩點之間高度)測試模式Hor(blinking):three-point measurement (height between two points)三分測量One-point(Act/Hor/Hgt/Ang)measurement單點測量(measurement order:1-2-3-4-2,then repeat)測量順序從 1-2-3-4-2，然后重復Target point 目標點Internal display(“l(fā)inear distance mode”)內部展示，直線距離模式(display will

6、 be different depending on the setting mode.)顯示的不同取決模式set your desired mode.設置你想要的模式Aim at the target .瞄準Press POWER button to measure，keeping the button pressed allows continuousmeasurement of up to 20 seconds.按電源按鈕保持20秒來衡量Results display example of each mode結果顯示每個模式的例子Act :Linear distance mode直線距離

7、模式Hor: horizontal distance mode水平距離模式Ang:Angle mode角度模式Hgt: height mode高度模式Power turns off 30 seconds after the last operation,停止操作30秒后，電源關閉。External display reading instructions外 部顯示閱讀指令(Actual external display image)實際外部顯示圖像All data below is displayed simultaneously 同時顯示下面數據Act (linear distance)直線

8、距離Hor (horizontal distance)水平距離Hgt(height from horizontal)高度Ang (angle from horizontal)角度Measuring vertical separation (height between two points)測量垂直分離(高 度兩點之間)(measurement order :1-2-3-4-5-6-7-2,then repeat)(測量順序:1-2-3-4-5-6-7-2,然 后重復)1st target point 第一目標點2nd target point 第二目標點Internal display 內部

9、展示1、Display when the vertical separation (height between two points)mode is s elected顯示垂直分離(高度兩點之間)模式被選中2、Aiming at the 1st point瞄準第一點3、Press POWER button to measure 按電源按鈕來衡量4、Display of the height from horizontal level of 1st point 顯示從水平線到第一點的高 度5、Aiming at the 2nd target point針對第二點目標6、Press POWER

10、button to measure按電源按鈕來衡量7、Display of the vertical separation (height between two points)顯示兩點之間高度(This symbol indicates the display is blinking顯示器閃爍符號)External display reading instructions外 部顯示閱讀指令After the measurement of 1st target point (actual external display image)After the measurement of 2st t

11、arget point(display of the vertical height between two points)(actual external display image)Three -point measurement (height between two points)三分測量(高度兩點之間) (measurement order :1-2-3-4-5-6-7-8-2,then repeat) 1st target point 2nd target point3rd target pointWhen measuring 2nd and 3rd points please n

12、ote that angles should be between -75 and +75 from the horizontal level .if measurement fails ,the angle is beyond 土 75當測量第2和第3點請注意,-75之間的角度應該和+ 75的水平。如果測量失敗,75士角超出 Internal display1、Display when three point measurement mode is selected顯示當三個點測量模式被選中2、Aiming at the 1st point .瞄準第一點3、Press POWER butto

13、n to measure按電源按鈕來衡量4、Display of the horizontal distance to the 1st point.顯示第一點水平距離5、Aiming at the 2nd target point.瞄準第二點6、Press POWER button to measure按電源按鈕來衡量7、Display of the vertical separation (height from horizontal level to 2nd point).顯示垂 直分離(高度從水平到第二點)。8、Aiming at the 3rd target point.瞄準第三點9、Press POWER button to measure按電源按鈕來衡量10、Display of the vertical separation (height between 2nd and 3rd points)顯示垂直分離 (第2和第3點之間的高度)External display reding instructionsAfter the measurement of 1st target point(actual external display image)After the measurement of 2st target pointdisplay of the verti