瑞陽光電觸摸屏規格書

1、FILE No:AY/QC-13AEDIT:DATE:2006/07/13REV: A3手寫類觸摸屏規格成認書Writing-type Touch panel Specification品名/Product Name： 機種名/Product Number： 客戶名稱 / CUSTOMER NAME： 客戶確認/CUSTOMER APPROVE： 日期/APPROVE DATE: APPROVECHECKEDIT瑞陽光電ARAYON OPTICS(SUZHOU)CO.,LTD蘇州新區金莊街28號No.28,JINZHUANG ST.SUZHOU NEW DISTRICTSUZHOU JIANG

2、SU PROVINCE CHINACode:215011TEL:+86-512-6665-3358FAX:+86-512-6665-3368 :(2)水平180。方向：0.5千克力10分鐘;不可剝離；應滿足以下工程： 端子間阻抗：參照電氣特性欄；Horizontal 1800 direction: After 0.5Kg 10min there is no peeling;The result shall satisfy fallowing items:Resistance between terminals: refer to electrical characteristics itemI

3、TO FILM/F=0Kg.十_ g 口、-ITO GLASSFPC耐彎曲性 FPC pattern bending resistance彎曲半徑為7 mm,拉伸晨度=25 mm,速度為1500rpm;彎曲次數為10 萬次，應滿足以下工程：參照電氣特性欄Bending 100,000 times by radius 7mm, length of peeling stroke 25mm, Speed 1500 rpm; The result shall satisfy following items: Resistance between terminals: refer to electric

4、al characteristics item金手指處焊接性 Gold-finger sold heat溫度：235+/-5；時間：3-5秒；焊點光滑圓潤Temperature: 235+7-5; Time: 3-5 sec, sold-dot smooth surface6.出貨檢驗事項 Quality Control Notices每批交貨實施以下檢查，并附檢查報告Every batch of product will be tested on the following, and the test report will be attached:(1)夕卜觀 Appearance(2)操

5、作壓力測試 Operation pressure test(3)電氣特性 Electronic characters(4)回路阻抗 Loop resistance.其它 Others(1)觸摸屏的信賴性測試應放置在平板上，在非通電狀態下進行。The reliability test shall be done with the touch panel put on a flat board, and with the circuit open. (2)各實驗工程應在標準狀態下(235、60%10%RH)進行，除非有單獨的說明。Each test shall be done at a norma

6、l condition (23 5 60%10%RH) unless otherwise specified separately.保證 Warranty蘇州瑞陽光電對所有制造的成品在出貨后一年內保證此規格書上所提到的工程Arayon Optics (Suzhou) Co, Ltd warrants that all manufactured product to this specification for one year from date of purchase.附件 Attached file工程圖 Drawing包裝圖 Packing Drawing使用說明及考前須知 Illust

7、rate & Operation InstructionsCONTENTS0.目錄 Contents.范圍 Scope.外形 Shape結構 Structure外形尺寸 Shape dimension.特性 Characteristics使用、保存環境 Operation and storage電氣特性 Electrical characteristics機械特性 Mechanical characteristics光學的特性 0Ptical characteristics.外觀檢查 Appearance Inspection檢查規那么 Inspection Criteria檢驗基準書 Ins

8、pection standards線狀異物 Linear foreign object點狀異物 Dot-like foreign objectFilm 外表沒有折傷 No fold on film surface牛頓環 / 干涉線 Newton ring / Interference fringes凸出(包括波狀彎曲)Bulge (undulation included)Film外表：魚眼 Film surface: Fish eye凹凸點 knaggy Dot氣泡 Air bubble玻璃毛屑和裂縫 Chip and Crack of glass.信賴性測試 Reliability Test

9、環境實驗 Environmental Test耐久試驗 Durability Test.出貨檢驗事項 Quality Control Notices.其它 Others.保證 Warranty.附件 Attached file范圍 Scope本規格書為明確規范本公司產品模擬式觸控面板性能而訂定，當本規格書與其它個別規格書內容有抵觸情 況發生時，仍以本規格書標準為最優先。本規格書內容如有工程缺乏或內容需變更時.，須經由會議討論后 另訂之。This specification defines performance of input surfaces for our transparent ana

10、log touch panels. In the event of a conflict between this specification and applicable individual specification, this specification takes precedence. Items missing from this specification are to be decided subject to discussion.外形 Shape外形、結構和尺寸詳見圖紙Shape, structure and dimension are referred to attac

11、hed drawing結構 Structure結構 Structure所用材料Material used備注Remark上線 Top CircuitITO 薄膜 ITO FILM屈面防刮；單層膜;厚度:0.188mm Clear Hard-coating;Single layer Thickness: 0.188mm下線 Bottom CircuitITO 玻璃 ITO GLASS厚度:0.70mmThickness: 0.70mm結構 Structure所用材料Material used備注Remark上線 Top CircuitITO 薄膜 ITO FILM屈面防刮；單層膜;厚度:0.18

12、8mm Clear Hard-coating;Single layer Thickness: 0.188mm下線 Bottom CircuitITO 玻璃 ITO GLASS厚度:0.70mmThickness: 0.70mm批注yl:根據實際情況填寫批注y2:根據實際情況填寫2.2 夕卜形尺寸 Shape dimension工程Item尺寸 Dimension單位Unit外形尺寸Out Dimensionmm可視區View Areamm動作區 Active Areamm絕緣點大小及間隔Spacer Dots & Pitch0.03、Pitchi.0mm3. 特性 Characteristic

13、s3.1 使用、保存環境 Operation and storage工程Item值（條件）Value （conditions）備注Remark使用溫度范圍Operation temperature & Humidity濕度20%90%：不可有結露 一2060Humidity： 20-90% non dew condensation20C60單體狀態下In a single substance保存溫度范圍Storage temperature & Humidity濕度20%90%：不可有結露 一3070Humidity： 20-90% non dew condensation一 30c70單體狀

14、態下In a single substance3.2 電氣特性 Electrical characteristics工程Item值 Value備注Remark最大電壓 Maximum voltage直流7V DC7V端子間阻抗Resistance between terminalsX方向（Film面）：280530Q X direction Film side: 280530。Y方向（Glass面）：480910。Y direction Glass side: 480910。直線性LinearityX方向：1.5%以內X direction: within 1.5%測試方法如下圖 Testin

15、g method as following drawingY力問：1.5%以內Y direction: within 1.5%V Measured Volume:VxX-Axis/vx Voltage - / 、Ideal Volume:Vp-Y-AxisA Positions B線性 Lirearity= I (Vp-Vx) / (Va-Vb) I x100 (%)Va=起點輸入電壓 Input vcdtage at start pointVb=終點輸入電壓 Input voltage at end point測試力 Test force:150gf絕緣阻抗Insulation resist

16、ance直流25 V 20MQ以上DC 25V 20MQ or more連接X+ X-和丫+ 丫，使用25V DC在X和Y測試。Connect X+ X- and Y+ Y-, apply 25V DC between X and Y for perform measurements響應時間 Chattering10毫秒以下10 msec or less額定電壓Rated Voltage直流5VDC 5V3.3 機械特性 Mechanical characteristics工程Item性能 PerformanceRemark備注輸入方法Input method用專用筆或手指觸控Use of a

17、n exclusive pen or finger動作荷重Load upon operation專用筆Exclusive pen80g 以下80g or less使用筆來進行操作或測試時.，其筆尖端 材質必須符合以下條件：筆尖材質：Polyacetal (聚纖維酯) 筆 端：筆徑$3.0 mm、外表弧度 R 0.8 mmOperation and measurement with a pen must be carried out under the following tip conditions :Stylus pen material : POM (Polyacetal)Tip : Di

18、ameter 3.0mm, SR 0.8 mm手指輸入 Finger80g以下 80g or less必須利用特定物質來代替手指進行操 作和測試，其材質必須符合以下條件 Operations and measurement methods simulated for a finger must be carried out under the following tip conditions :材 質：硅橡膠(硬度：SHORE A 30 度)頂 端：筆徑f 12 nm1、外表弧度R 12. 5 mmMaterial : Silicon rubber ( Hardness : 30 Hs)Tip

19、 : Diameter 12.0 mm, SR 12.5 mm外表硬度Surface hardness鉛筆硬度3H以上Pencil hardness: 3H or more依據JIS K5600試驗方法It complies with the way of test method JIS K5600備注：由絕緣點的大小及間距來決定操作壓力的大小。Remark: The operation force depending on the diameter & pitch of spacer dot.3.4 光學的特性 Optical characteristics工程Item性能 Performa

20、nce備注RemarkTotal light transmittance 全光線透過率80%以上80% or moreJIS K7105霧值Haze5%以下5% or lessJIS K7136Film規格Film specification亮面，有一定外表硬度Clear type with hard-coating surface4.夕卜觀檢查 Appearance Inspection4.1 檢查規那么 Inspection Criteria工程Item條件 Conditions備注Remark檢查范圍Inspection area應用區域：可視區Application Area; Vie

21、w Area*所有的外觀不良只要是在可視區以外對產品功能不造成影響均不考慮在內 Any defects in invisible shall be ignored unless they affect electrical performance.*所有可以使用軟布用酒精擦拭得掉的污染物均不考慮在內Contamination that can be cleaned using soft cloth with ethyl alcohol does not apply to these visual criterion.檢查條件 Inspection Conditions視力1.0及以上的健康成人

22、(帶眼鏡亦可)，物體與檢測者眼睛距離20到30厘米 處檢測。The inspection should be conducted by a healthy inspector with a vision of 1.0 or above (eyeglasses acceptable), and at a distance 20 to 30cm between the object and the inspectors eye.使用機器：熒光燈30WInspection device: florescent light 30 W檢查環境Inspection Environmentl；：；：；：:;

23、：l- Eyes/mw Lamp第Approx. 60/ 、Touch Panel1-黑色泡棉(Black Foam)4.2 檢驗基準書 Inspection standards產品可視范圍外假設沒有裂縫，刮傷，異物等外觀不良影響產品電氣特性的，也可接受。For areas outside the visible range, it is acceptable if there is no crack, scratch, or foreign objects that can greatly affect the electric performance of this product.限度樣

24、品將被用于本基準中未描述到的裂縫，刮傷或者異物等外觀不良。Limit samples shall be used for cracks, scratch, or foreign objects which are not described in this standard.4.3 線狀缺陷(W=寬度、L=長度)Linear foreign object (W=Width, L=Length)寬度Width (mm)長度Length (mm)基準 Judge criterion備注RemarkWW0.05LW4不計 IgnoredLW41 個 1 objectW0.09不接受Reject4.4

25、 點狀異物(D=長徑)Dot-like foreign object (D = longest diameter)4.5 Film 外表沒有折傷 No fold on film surface平均直徑 Average diameter (mm)基準 Judge criterion備注RemarkDW0.10不計 Ignored2個以上缺陷 Up to total two defects0.100,20不接受 Reject4.6 牛頓環 / 干涉線 Newton ring / Interference fringes根據4.1 外觀檢查方法確認 To be confirmed according

26、 to No.4.1 inspection of appearance 夕卜觀牛頓環限定個數 Appearance Inspection Limit sample:工程基準ItemsJudge criterion備注Remark在整個觸摸屏檢查區域內超過1/3范圍;不接受The area covered by Newton Ring is more than 1/3 of the whole TP surface; Reject堂如在整個觸摸屏檢查區域內小于1/3范圍，并且在有照明環境下不影響透光率Regular及失真;接受The area covered by Newton Ring is

27、less than 1/3 of the whole TP surface, and it doesnl affect transmittance and clarity of TP under the lighting ambient;Accept在整個觸摸屏檢查區域內在照明環境下超過1/2范圍;不接受The area covered by Newton Ring is more than 1/2 of the whole TP surface under the lighting ambient; Reject在照明環境下牛頓環有影響清晰度和透光率;不接受(不計牛頓環尺寸),列必If th

28、e Newton Ring affect the transmittance and clarity under lighting. ambient, it is NG (Neglect the Newton Ring size)egu ”在整個觸摸屏檢查區域內小于“2范圍，并且在有照明環境下不影響透光率及失真;接受The area covered by Newton Ring is less than 1/2 of the whole TP surface, and it doesnt affect transmittance and clarity of TP under the ligh

29、ting ambient; Accept4.7 凸出(包括波狀彎曲)Bulge (undulation included)膜鼓起在0.40mm高度范圍內判定為合格品。The ITO film Bulged below 0.40mm, ifs ok.0.4mm or less0.4mm或以下Glass凸出BulgeFilm、 4.8 Film外表：魚眼 Film surface: Fish eye平均直徑Average diameter (mm)基準 Judge criterion備注RemarkDW0.20不計 Ignored最多6個MAX 6 Pieces最多2個MAX 2 PiecesD0

30、.60不接受Reject4.9 凹凸點 knaggy Dot平均直徑 Average diameter (mm)基準 Judge criterion備注RemarkDW0.20不計 Ignored2個以上缺陷 Up to total two defects2個或2個以下2 objects or less1 個 1 objectD0.50不接受Reject4.10 氣泡 Air bubble平均直徑 Average diameter (mm)基準 Judge criterion備注RemarkDW0.15不計 Ignored3個以上缺陷 Up to total three defects0.15

31、DW0.303個或3個以下3 objects or less0.300.50不接受Reject4.11 玻璃毛屑和裂縫(t =玻璃厚度)Chip and Crack of glass (t = glass thickness)工程Item尺寸 Size (mm)長度 Length (mm)接受個數 Acceptable Qty角CornerXW2OJV：假設有任何一個毛屑或裂 縫超過所給的X, Y, Z值，那么 不接受。0 pee: Judgedunacceptable if there is any one chip or crack exceeding the permissive val

32、ue of X, Y, or 乙YW2ZWt角以外的地方Other than cornerXW3。片：假設有任何一個毛屑或裂 縫超過所給的X, Y, Z值，那么 不接受。0 pee: Judged unacceptable if there is any one chip or crack exceeding the permissive value of X,Y,Z.每邊2個或更少：它們要小于 所給的值。Two or less for each side: Those less than these values.YZt進行性的裂縫 或者毛屑 Progressive Crack or chi

33、pJo片：假設有任何進行性的裂縫或毛屑，不接受。0 Pcs: Judged unacceptable if there is any progressive crack or chip.5.信賴性實驗內容Reliability Test5.1 環境實驗 Environment Test工程Items內容Contents備注Remark高溫保存High temperature preservation溫度70,放置120小時；(2)室溫放置24小時以上；(3)然后測量以下 工程：(1)Store at 70 for 120 hours; (2) Keep at a room temperatur

34、e for more than 24 hours; and (3) Measure (satisfy) the following items: 端子間阻抗：參照山氣特性欄Resistance between terminals: refer to electrical characteristics item ;直線性：參照電氣特性欄 Linearity: refer to electrical characteristics item;絕緣阻抗：參照電氣特性欄 Insulation resistance: refer to electrical characteristics item)低

35、溫保存Low temperature preservation(1)溫度30,放置120小時;(2)室溫放置24小時以上;(3)然后測量以 下工程：(1)Store at -30 for 120 hours; (2) Keep at a room temperature for more than 24 hours; and (3) Measure (satisfy) the following items: 端子間阻抗：參照M氣特性欄Resistance between terminals: refer to electrical characteristics item;直線性：參照電氣特

36、性欄 Linearity: refer to electrical characteristics item;絕緣阻抗：參照電氣特性欄 Insulation resistance: refer to electrical characteristics item高溫高濕保存High temperature & high humidity(1)溫度60濕度90%,放置120小時；(2)室溫放置24小時以上然后測 量以下工程：(1)Store at 60 and 90% RH for 120 hours; (2) Keep at a room temperature for more than 2

37、4 hours; and (3) Measure (satisfy) the following items:端子間阻抗:參照電氣特性欄Resistance between terminals: refer to electrical characteristics item;直線性：參照電氣特性欄 Lineality: refer to electrical characteristics item;絕緣阻抗：參照電氣特性欄 Insulation resistance: refer to electrical characteristics item冷熱沖擊測試Heat shook test

38、(1)-30(60分)80(60分)共10次循環;(2)室溫放置24小時以 上;(3)然后測量以下工程：(1)30(60min)-*80(60min)total 10 cycles, (2) Keep at a room temperature for more than 24 hours; and (3) Measure (satisfy) the following items:端子間阻抗：參照電氣特性欄Resistance between terminals: refer to electrical characteristics item;直線性：參照電氣特性欄 Linearity:

39、refer to electrical characteristics item;絕緣阻抗：參照電氣特性欄 Insulation resistance: refer to electrical characteristics item5.2 Durability Test 耐久試驗工程Items內容 Contents備注Remark耐敲擊Hitting Durability耐久劃線Sliding Durability(1)使用Placental (POM)鉛筆(ROS)敲擊100萬次。(2)然后測量以下項 目：(1)Hit 1,000,000 times with a Placental (POM) pencil (R0.8); and (2) Measure (satisfy) the following items:荷重：2NLoad:2N速度：2次/secSpeed: 2 times/sec端子間阻抗:參照電氣特性欄Resistance between terminals: refer to electrical characteristics item;直線性：參照電氣特性欄 Linearity: refer to electrical characteristics item;絕緣阻抗：參照電氣特性欄 Insulation resistance