同軸電纜施工工具.ppt

1、同軸電纜施工工具,同軸電纜的布放與屏蔽型雙絞線類似 使用符合同軸電纜結構特點的工具進行剪切及剝線 專用連接器及端接工具 雙絞線驗證與認證設備同樣適用于同軸電纜,同軸電纜分類,同軸電纜結構,中心導體要與屏蔽層保持等距以確保信號傳輸性能 標準規定：屏蔽電纜的彎曲半徑應至少為電纜外徑的610倍,同軸電纜施工工具剪切,截面被壓扁,These just wont do,同軸電纜施工工具剪切,正確的剪切工具,45074,45075,Data T - Cutter 剪線鉗 多股通信電纜，直徑0.5in.(12.7mm) 同軸電纜RG-59/U、RG-58、RG-6 適合于剪切軟線 柔軟的手柄套便于握持 鎖定

2、銷使工具便于裝在工具套中,同軸電纜施工工具剝線,Stripping coax F-style,45-262 Stripmaster,45-524 Coax Stripper,30-433 Combo Tool,同軸電纜施工工具剝線Coax Stripmaster,Spring action grips & strips Speeds up 2-step stripping Different blades for: RG6 RG59 RG6 Quad,45-262,同軸電纜施工工具剝線Stripping coax with the Stripmaster 45-262,1. Place cab

3、le in smaller hole ” protruding,2. Squeeze handles together firmly & quickly,3. Place cable in larger hole ” protruding, squeeze,4. Stripped cable,同軸電纜施工工具剝線Stripping with the Coax Stripper 45-524,1. Set sliding window to cable size,2. Place cable in stripper with 1/8” protruding,3. Rotate stripper

4、in direction of lettering,4. Remove cable from stripper,5. Remove slugs,6. Stripped cable,同軸電纜施工工具剝線Adjusting the Coax Stripper 45-524,4. Check by restripping cable. What was the left side is now the right side upside down!,1. Remove hex wrench from handle,2. Turn stripper over,3. Insert wrench into

5、 adjusting grommets. Adjust by rotating 1/3 of way around at a time,同軸電纜施工工具剝線Replacing the blade cassette,Pull front door open Lift cassette up & out Insert new cassette & close door,同軸電纜施工工具端接About “F” Connectors,One-piece Most preferred, easiest installation Two-piece More pullout strength Twist-

6、on What twists on will twist off,The number one cause of video distribution problemsis tightening F connectors finger tight. Tighten them with an F connector tool.,同軸電纜施工工具端接 About “F” Connectors,Must be used for all open CATV outlets Eliminates leakage and ingress, which lead to poor signal quality

7、,同軸電纜施工工具端接F-Connector Tool,Using leverage to install an F connector will seat every connector properly Most video signal problems are caused by loose connections. Tighten all connectors with an F-Connector tool.,35-046,Thread connector onto end of tool,Push connector onto stripped cable,同軸電纜施工工具端接C

8、oax Strip & Crimp Tool,Cuts, Strips & Crimps RG-6 & RG-59 No need to carry separate tools Good for occasional contractor use,30-433,同軸電纜施工工具端接Terminating coax - CrimpMaster,Consistency & repeatability More leverage, less installer fatigue The same crimp every time 28 interchangeable dies For the ins

9、taller with more than an occasional crimp to do,30-506,與Crimpmaster 配合使用的同軸電纜連接器壓接模塊,同軸電纜施工工具剝線Stripping coax - BNC,Accuracy, efficiency, repeatability,45-520 Coax Stripper,Cut center conductor with35-060 CenterConductor Cutter,同軸電纜施工工具剝線To use the 45-520,1. Set sliding window to cable size,2. Place

10、 cable in stripper with 1/4” protruding,3. Rotate stripper in direction of lettering,4. Remove cable from stripper,5. Remove 1st two slugs,6. Remove 3rd slug by bending cable,同軸電纜施工工具剝線Center Conductor Cutter 35-060,1. Stripped cable,2. Lay side of cutter against white dielectric,3. Finished cable,同

11、軸電纜施工工具端接BNC/TNC Connectors,Primary use today is for video/security installations Was an early data connector Looks like a difficult termination, but can be the easiest,同軸電纜施工工具端接Three-piece BNC,Recommended Fastest Easiest Captive contact pin Gas-tight crimp,Captive Contact Pin,同軸電纜施工工具端接Two-piece B

12、NC,Strip to Braid, Peel Back,Less expensive More labor No captive contact pin No gas tight crimp,同軸電纜施工工具端接Twist-on BNC,Quickest, easiest Least reliable No captive contact pin No gas-tight crimp Can be affected by thermal change Installers worst nightmare Intermittent failure,同軸電纜施工工具端接Terminating B

13、NC Connectors,1. Close CrimpMaster to 1/8” open,2. Place center contact pin point down into smallest crimp nest,Wrong side up,3. Place center conductor all the way into center contact pin and crimp,4. Rotate dielectric to bend back braiding,同軸電纜施工工具端接Terminating BNC Connectors,1. Seat connector body onto dielectric, underneath the braiding, listen for click of captive contact pin,2. Seat the ferrule against the connector body with equal, opposing force,3. Squeeze handles together completely,4. Finished Connector,同軸電纜施工工具端接Coax Strip & Crimp Tool 30-433,C