紡絲現場常用英語專業詞匯

1、紡絲常用英語一、工藝管理Direct melt spinning (plant)直接紡（工廠）polymerization process 酯化工藝Polymer booster pump聚酯增壓泵control the winding tension of the yarn 控制絲條卷繞張力spinning speed 紡絲速度isothemal 等溫humidity 濕度air flow 風向properties 特性粘度location of oil jet 油嘴位置wingding speed 卷速temperature 溫度Solidified 凝固spinning tension

2、紡絲張力yarn tension(T1T2T3)絲條張力winding tension 卷繞張力spinning process 紡絲工藝helix angle 交叉角emulsion concentration 濃度output/through put 泵供量traverse control 橫動控制pump capacity 泵規格pump revolution 泵轉速melting temp. 熔體溫度molten polymer 熔體softening temp. 軟化點pack internal pressure 組件壓力melt viscosity 熔體粘度glass transl

3、ation temp. 玻璃化溫度conc. Emulsion 濃度air presure 風壓bunched together 集束air velocity 風速cohesiveness內聚性air flow 風向yarn contact angle 絲條接觸角度specified value設定值pack internal pressure 組件壓力polymer pressure 熔體壓力quenching air 側吹風extrude 擠出pump efficiency 泵效率specific property特性actual content 實際成分cationic dyeable

4、陽離子可染active content 活性成分keep good spinability 保持紡絲性能二、質量管理Uster eveness 條干不勻率opu（oil pick up）含油率titer 纖度denier 旦尼爾elongation 伸長filament diameter 纖維直徑tenacity 強度package density 卷裝密度twister 捻度micron 微米litre 升denier checking machine纖度檢測儀器tensile tester 強伸儀hand-held instrument 手持測量儀classify 分等bar 巴lap 疊

5、絲tight spot 緊點routine sampling 常規取樣Downgrade/degrade降等unit 單位三、設備polymer filter 過濾器quench separator 側吹風隔板jacket夾套a set of ceramic guides 一組瓷件oil guide 油嘴瓷件drip pan 紡絲用的接油盤spinneret 噴絲板set screw 頂緊螺釘pack /spin pack 組件caliper 卡鉗gear pump 齒輪泵Static mixer 靜態混合器suction gun 吸槍shutter 切絲器drive roller 主動輥wa

6、sher墊圈godet roller 導絲輥panel 儀表板take-up machine/winder卷繞機controller 控制器quenching chamber 側吹風室interfloor-tube shutter紡絲甬道隔板cap crews 螺帽HTM reboiler 熱媒爐idler gears 從動齒輪stoppage 故障a sharp brass or aluminium wipe stick 銅/鋁鏟刀dismantled parts 組件拆卸plug 塞teeth spaces of the gears 齒輪間隙port 孔face of the spinne

7、ret 噴絲板面capillary 毛細孔lenz ring 卡簧wire mesh 金屬網pigtail guide 豬尾巴瓷件filter 過濾器spin beam/block 紡絲箱體squeeze ring 分配板pump parts 計量泵備件Inlet packing 內模板jig 鑷子optical sensor 光學傳感器extrusion hole 擠出孔gauge 液位計Filter mesh 過濾器網shaft 軸filter 過濾器brass rod 熟銅錘Alumina Sand 氧化鋁idler spindle 從動輪filteration medium 過濾介質d

8、riving spindle 主動輪cap screws/Allen bolt 螺母spin finish pump 紡絲油劑泵Allen key 內六角扳手discard 非插件lubrication 潤滑quench chamber damper valve 側吹風調節閥metal filter 金屬燒結網anemomaster 風速儀hexagon wrench 內六角扳手manifold 總管flowmeter 流量計drive motor 傳動馬達fine holes of spinneret 噴絲板微孔inverter 變頻器seal 密封distributor 分配管take-u

9、p machine 卷繞機intermingling nozzle 網絡噴嘴spinning duct 紡絲甬道doffing cart 落絲小車POY cart 絲餅小車coupler 聯軸節Reactor 聚酯反應器air hose 氣管aspirator 吸絲器metering pump 計量泵vessel 容器a set of godets一組導絲輥chip cutter 切粒機 ring 環pre-interlace jet 預網絡器surface roughness 表面粗糙度transfer line 輸送管線roller bail parallelism 分絲輥平行度 chip

10、 silo 料倉precision 精度parts 備件tray 隔板pack body 組件殼體pack lid 蓋子air wrench 氣動槍oil jet 油嘴wrench扳手四、管理人員Team Leader 組長Dedicated Manufacturing Staff 指定的操作人員Quality Operator Coverage 質量員Maintenance Staff 維保人員Quality Manager 質量管理人員Maintenance Manager 維保管理人員Team Communications Coordinator 協調人Training Speciali

11、st 培訓Top Manager from Plant 3 三廠高管Team Technical Leader 技術組長Lab Manager 分檢管理人員DTY Quality Control Manager DTY質量控制主管Manufacturing Shift Leaders 值班長Target Machines 生產線五、檢查管理the water temp should be around 35C 水溫保持在35攝氏度左右 yarn fluctuation 絲條波動conditioned air 空調風at patrol 巡檢時hammer 錘擊OLT rejection 張力報警

12、one more treatment of T.E.G for 6 hours at a temp.270 270°TEG處理6小時以上Monitoring unit 監視shut down 停車check point 檢測點clean all these parts with the help of DM water and if necessary in ultrasonic and dry all the parts. 先用脫鹽水清洗，再用超聲波清洗，最后吹干 defective pack 有缺陷的組件 pack tightening 組件緊固energy consumptio

13、n 能耗intermediate 中間物Squeeze filter bulge 膨脹refit 改裝corrective action 改進rotate 旋轉requirement from the customer 客戶需求serious accident 嚴重事故routine maintenance 例行維修 proper action 規范操作polymer leakage 漏漿polymerization section 聚酯部份heavy denier 粗旦replacement 置換Light denier/fine denier/small denier 細旦 torque

14、扭矩OLT event 張力事件replace 更換overthrow 絆絲loosen pack bolt 擰開組件螺栓original date 起始日期polymer dust 漿塊extra quench stock 備用側吹風板drip 滴dye ability 染色能力 certain position 確定的錠位routine work 常規作業wiping of spinneret 鏟板mounting plate 固定Plugged or partially plugged holes 堵孔contamination 雜質pack dismantling device 組件分

15、解裝置punch 打孔pack leakage 組件漏漿bent filaments 彎頭絲yarn path stability 絲道穩定inspect with microscope 鏡檢before works over 下班之前release limits 定等出廠控制線temperature uniformity 溫度均勻trade standard 行業標準store 存貯state standard 國家標準troubleshoot 故障檢驗period of validity/ end day 有效期pack change interval 組件更換周期cross sectio

16、nn 橫截面shut off 切斷soiling of spinneret surface 噴絲板面臟depend on inner pressure and yarn break 由組件壓力和斷頭情況決定cleanness 清潔processing room condition 環境條件eye observation 目測abnormal sound 異響dimension 尺寸六、材料 degreaser 去(油)污劑infrared ray 紅外線silicone spray 硅油A fine grade polish paper 高級拋光紙cloth 布minor 鏡子Antisept

17、ic 防腐劑DM Water 脫鹽水Raw Finish Oil 原油劑Dowtherm vapour 熱媒蒸汽emery cloth 砂布/金剛砂布liquid dowtherm 液態熱媒cleaner 清潔劑HTM vapour 熱媒蒸汽finish oil 紡絲油劑single filament 單絲magnifying glass 放大鏡waste 廢絲cardboard 紙板comprssed air 壓縮空氣sample 樣品七、生產Vacuum pyrolysis真空爐清洗strip 剝絲fluidished bath 流化床清洗yarn path 絲道salt bath 鹽浴/

18、堿洗ultrasonic 超聲波清洗TEG bath 三甘醇清洗vibration level 振動水平taken out 落筒Cleaning process 清洗工藝change over 換筒cleaning cycle time清洗周期eye observation 目測emulsion preparation 油劑調配clean spinneret surface 鏟板finish tube cleaning 油劑管線清洗single filament yarn flow 飄單絲hot water cleaning of finish system 油劑管線系統的熱水清洗batch 批次Product chang