




版權說明:本文檔由用戶提供并上傳,收益歸屬內容提供方,若內容存在侵權,請進行舉報或認領
文檔簡介
1、電纜管配置與敷設Cable pipe configuration and laying工序Process檢驗項目Check items性質Property質量標準Quality standard檢驗方法和器具Inspection method and instrument電纜管制作Cable pipe fabrication外觀檢查appearance inspection 金屬管metal pipe表面Inner surface光滑,無毛刺smooth,no burrs觀察檢查visual check外表面Outside surface無穿孔、裂縫、顯著的凹凸不平與銹蝕no hole,cra
2、ck,obvious unevenness or rust塑料管plastic pipe敷設溫度laying temperature按設計規定as per the design stipulation按圖紙檢查并檢查出廠合格證check as per the drawing and check the factory certificate管材強度pipe strength切斷口(管口)nozzle光滑smooth觀察檢查visual check彎曲部分bending section無裂縫與顯著的凹癟no crack or obvious concavity每根電纜管的彎頭數No. of ea
3、ch pipe bending elbows一般彎頭common elbow3個 not more than 3觀察檢查visual check直角彎頭right angle elbow2個 not more than 2彎曲半徑bending radius主要primary與所穿電纜彎曲半徑匹配suitable for the cable bending radius用樣板檢查check with the sample電纜管彎扁度cable pipe bending flatness degree不大于1/10電纜管外徑not bigger than 1/10 of the cable pi
4、pe OD用尺檢查check with the tape電纜管檢查Cable pipe inspection電纜管徑ID of the cable pipe按設計規定,且不小于1.5倍電纜外徑as per design stipulation, and not less than 1.5 times of the cable outside diameter 用尺檢查check with the tape管暢通檢查non-obstruction check主要primary光滑,無積水,雜物smooth, no seeper or sundries 用0.85倍管徑拉線球檢查check wit
5、h the bracing wire ball(0.85 times pipe inside diameter)敷管Pipe laying路徑method按設計規定as per design stipulation對照?qǐng)D紙檢查check comparing with the drawings明敷exposed laying單管敷設single pipe laying橫平豎直horizontal and vertical觀察檢查visual check排管敷設pipe bundle laying管口高度nozzle elevation一致identical觀察檢查visual check彎曲弧度
6、bending radian measure觀察檢查visual check引至設備的管口位置lead to the nozzle of the equipment便于電纜與設備連接,并不妨礙設備拆裝和進出convenient to connect the cable and the device, not obstruct the equipment dismounting and passing觀察檢查visual check與熱力管道,熱力設備之間的凈距the net distance between pipe and the heating pipe, heating equipmen
7、t平行敷設parallel laying主要primary1m,不宜敷設于熱力管道上部1m, not good to lay above the thermal pipes用尺檢查check with the tape交叉敷設cross laying 0.5m與保溫層之間凈距the net distance between the pipe and the thermal insulator 平行敷設parallel laying主要primary0.5m交叉敷設cross laying0.2m直埋bury directly直埋管距地面深度(混凝土除外)the depth below the
8、ground(except concrete)700mm用尺檢查check with the tape伸出建筑物散水坡的長度the length beyond the building bulk water slop250mm伸出道路路基長度length beyond the roadbed2m伸出地面的排管外觀檢查appearance check of the pipe bundle beyond the ground排列整齊,高度一致arrange in good order and at the same level觀察檢查visual check引入建筑物和建筑物的埋置深度(混凝土除外
9、)the embedded depth inside the building and the depth inside the building(except the concrete)300mm-500mm用尺檢查check with the tape電纜管道與其他管道、道路、建筑物之間平行和交叉時的凈距the parallel and across net distance between the cable trench and other trenches, roads and buildings主要primary按GB 501681992表5.4.3規定As per GB 5016
10、81992 Stipulated in chart 5.4.3電纜管連接Cable Pipe connection金屬管metal pipe套管連接bushing pipe connection 套管長度bushing pipe length1.5D-3D電纜管外徑1.5D-3D cable pipe OD用尺檢查check with the tape外觀檢查appearance check焊接牢固Welded firmly觀察檢查和用鍍鋅鐵絲綁棉紗通入管檢查visual checkand check through inserting the cotton yarn tied galvani
11、zed iron wire 絲扣連接管端套絲長度mm pipe end mantle fiber length1/2管接頭長度1/2pipe joint length用尺檢查check with the tape外觀檢查appearance check連接牢固,密封良好Connected firmly, good seal觀察檢查visual check防腐漆檢查anti-corrosive paint check涂刷均勻,漆層完好Bushed uniformly and good paint layer硬質塑料管hard plastic pipe套接casing connection套管兩側
12、封焊牢固,密封良好the welding at both ends is firm, sealed well觀察檢查visual check插接 insert connection插接面用膠合劑粘和牢固,密封良好the insert surface is glued firmly by the agglutinant and sealed well.插入深度insert depth 1.1D-1.8D電纜管徑1.1D-1.8D cable pipe inside diameter用尺檢查check with the tape硬質塑料管補償裝置安裝hard plastic pipe compen
13、sation device installation按GB 50168-1990規定As per GB 50168-1990 stipulation對照?qǐng)D紙或規檢查check comparing with the drawing and specification金屬軟管固定與連接fasten and connection of the metal soft pipe主要primary牢固、緊固firm and tight用手扳動檢查pulling check with hand其他Others鍍鋅管galvanized pipe鍍鋅層完整the galvanized layer is com
14、plete.觀察檢查visual check電纜管接地cable pipe ground主要primary牢固,導通良好firm, good conduction扳動并導通檢查Pull and conduction check電纜支架(橋架)制作與安裝Cable frame (cable tray) fabrication and erection工序Process檢驗項目Check items性質 Property質量標準Quality standard檢驗方法與器具Inspection method and instrument電纜架配制Cable frame fabrication型鋼檢
15、查Section steel check外觀檢查Appearance check無顯著扭曲,切口無卷邊、毛刺N(yùn)o obvious contortion, no 觀察檢查visual check規格Specification按設計規定As per design stipulation對照?qǐng)D紙檢查check comparing with the drawing電纜架Cable frame電纜支架層間允許最小距離The permitted smallest distance between the cable frame layers 按GB 50168-1992中 表4.0.2規定As per G
16、B 50168-1992: CHART 4.0.2 stipulation用尺檢查Check with the tape焊接welding主要Primary牢固 firm觀察檢查visual check電纜托架配制cable tray fabrication按設計規定as per design stipulation對照?qǐng)D紙檢查as per drawing to check鍍鋅層galvanized layer完好perfect觀察檢查visual check預埋件embedded members布置arrange按設計規定as per the design stipulation對照?qǐng)D紙檢查
17、as per the drawing to check固定強度f(wàn)asten strength主要Primary牢固firm用手扳動檢查check by pulling with hands電纜支吊架安裝Cable branch hanging frame erection布置與間距arrangement and spacing主要Primary按設計規定as per design stipulation對照?qǐng)D紙檢查as per drawing to check最上(下)層橫撐至溝頂或樓板距離The distance between the top(bottom) brace and the t
18、rench top or the floor slab按GB 50168-1992中 表4.0.3規定as per GB 50168-1992: chart 4.0.3 stipulation對照規檢查as per specification to check水平布置電纜架高低誤差the deviation of the parallel arrangement of the cable frame5mm用拉線和尺檢查check with the bracing wire垂直布置電纜架左右誤差left and right deviations of the vertical arrangeme
19、nt of cable frame用鉛墜和尺檢查check with the plummet在有坡度的電纜溝或建筑物上電纜架布置arrange the cable frame in the cable trench with slope or on the building與電纜溝或建筑物同坡度布置arrange at the same slope degree of the cable trench or building觀察檢查visual check電纜架固定 fasten the cable frame主要Primary牢固firm扳動檢查check by pulling電纜托架安裝c
20、able tray installation按設計規定as per design stipulation對照?qǐng)D紙檢查as per drawing to check組裝后的鋼結構豎井檢查check the steel structure vertical shaft after assembling垂直誤差(m)m vertical deviation (mm)0.2%豎井高度0.2% shaft height用尺檢查Check with tape支架橫撐水平誤差(mm) level deviation of the support horizontal brace (mm)0.2%豎井高度0.
21、2%shaft height用尺檢查Check with tape對角線誤差mmDiagonal line deviation (mm)0.5%豎井對角線長度0.5% shaft diagonal line length觀察檢查visual check外觀檢查 appearance check無傷損,變形no damage, distortion觀察檢查visual check其他電纜架焊縫與豎井保護罩油漆Cable frame weld seam and shaft protective casing paint完整complete觀察檢查visual check電纜架全長接地Cable f
22、rame overall grounding 牢固,全長導通良好firm, good overall conduction 對照規檢查Check comparing with the specification生產廠房與隧道、溝道的電纜敷設Cable laying in the workshop and channel, trench工序Process檢驗項目Inspection items性質Property質量標準Quality standard檢驗方法與器具Inspection method and instrument敷設前檢查Check before laying電纜Cable 型號
23、、電壓與規格model, voltage and specification 按設計規定as per design對照?qǐng)D紙檢查Check comparing with drawing外觀檢查appearance check無機械損傷和滲油no mechanical damage and oil infiltrate 觀察檢查visual check絕緣檢查insulation check主要Primary 良好Fine 用兆歐表檢查check with the megger 敷設路徑laying route按設計規定As per design對照?qǐng)D紙檢查Check as per drawing
24、敷設溫度Laying temperature 按GB50168-1992規定as per GB50168-1992 stipulation對照規檢查check as per specification 端頭密封end sealing 油紙絕緣電力電纜oil paper insulation power cable鉛封密實,無滲油Fine lead sealing, no oil infiltrate觀察檢查visual check交聯聚乙烯電纜XLPE cable可靠,嚴密Reliable, tight充油電纜oil filled cable按GB50168-1992規定as per GB50
25、168-1992 stipulation對照規檢查Check as per specification 電纜敷設Cable laying油紙電纜敷設位差paper cable laying level difference主要Primary 按GB50168-1992規定as per GB50168-1992 stipulation對照規檢查電纜敷設記錄check the cable laying record as per the specification電纜彎曲半徑Cable bending radius 主要primary 用樣板檢查Check as per sample與熱力設備、管
26、道之間凈距the net distance between cable and thermal equipment, pipe平行敷設parallel laying 主要primary1m,不宜敷設于熱力管道上部1m, not appropriate to lay cable above thermal tubes 用尺檢查Check with tape交叉敷設Cross laying 0.5m與保溫層之間凈距the net distance between cable and heat preservation layer平行敷設parallel laying 主要Primary 0.5m交
27、叉敷設Cross laying 0.2m電纜排列Cable arrange外觀檢查appearance check排列整齊,彎度一致,少交叉tidy, the same bending degree, less crossing觀察檢查Visual check交流單芯電纜排列方式AC single core cable arrange mode按設計規定As per design電纜標志牌Cable sign board 裝設位置Location 電纜終端、電纜中間接頭處cable ends, intermediary joint of cable 按GB50168-1992中,5.1.19條
28、要求As per GB5016801992, requirement5.1.19標志Sign 主要Primary 按GB50168-1992規定as per stipulation in GB 50168-1992對照電纜敷設清冊檢查check as per cable laying list固定fasten掛裝牢靠mount firm and reliably用手扳動檢查Check through pulling 規格specification一致identical觀察檢查visual check電纜固定Cable fasten 電纜支持點間距離the distance between th
29、e cable support points按GB50168-1992規定as per GB50168-1992用尺檢查Check with tape水平敷設Parallel laying電纜首末端與轉彎處、接頭兩端both ends and turning of the cable, both ends of the joint觀察檢查Visual check超過45°傾斜敷設slope laying of more than 45°主要Primary 電纜每個支持點each support point of the cable夾具型式clamp model按設計規定as
30、 per design對照?qǐng)D紙檢查check as per drawing交流單芯電纜固定夾具fasten clamp of the AC single core cable夾具無鐵件構成的閉合磁路no iron formed closed magnetic circuit for the clamp 觀察檢查visual check裸鉛(鋁)套電纜固定處保護protection at the bare lead (aluminum) 軟襯墊齊全、可靠Soft cushions are complete and reliable電纜固定強度cable fasten strength 牢靠rel
31、iable用手扳動檢查check through pulling敷設后檢查電纜外觀檢查appearance check主要Primary 無機械損傷和滲油no mechanical damage or oil infiltrate 觀察檢查visual check電纜孔洞處理treatment of the cable hole 電纜溝、隧道、豎井、建筑物與盤(柜)電纜出入口封閉良好the cable inlet and outlet in the cable trench, channel, shaft, building and panel( cabinet) are sealed wel
32、l. 管道電纜敷設Cable laying in the pipe工序Process檢驗項目Inspection items性質Property質量標準Quality standard檢驗方法與器具inspection method and instrument敷設前檢查Check before laying電纜Cable 型號、電壓、規格與長度Model, voltage, specification and length按設計規定As per design對照?qǐng)D紙檢查Check as per drawing外觀檢查appearance check無機械損傷和滲油No mechanical
33、damage or oil infiltrate 觀察檢查visual check絕緣檢查insulation check主要primary 良好Fine 用兆歐表檢查Check with megger電纜管Cable pipe暢通檢查non-obstruction check 部無積水、雜物No water, sundries 疏通檢查check through dredge徑inside diameter按設計規定As per design用尺檢查Check with tape電纜敷設Cable laying敷設路徑Laying route按設計規定As per design對照?qǐng)D紙檢查A
34、s per drawing to check端頭密封End 油紙絕緣電力電纜oil paper insulation power cable 鉛封密實,無滲油lead sealing tightly, no oil infiltrate觀察檢查visual check交聯聚乙烯電纜XLPE cable 防潮封端可靠,嚴密reliable anti-humidity, tight充油電纜Oil-filled cable按GB 50168-1992規定as per GB50168-1992電纜彎曲半徑Cable bending radius主要Primary 按GB 50168-1992規定as
35、per GB50168-1992用樣板檢查Check with the sample 交流單芯電力電纜AC single core power cable在支架上敷設laying on the support structure 布置在同側支架上Arrange on the same side support structure觀察檢查visual check在鋼管敷設Laying inside the steel pipe主要primary三相電纜共穿一管Three phase cable going through one pipe電纜標志牌cable sign board裝設位置Inst
36、allation location電纜終端兩端與接頭處both ends and joints of the cable觀察檢查visual check標志sign主要primary電纜線路設計編號、型號、規格與起訖地點;字跡清晰,不易脫落cable circuit design No., model, specification and beginning and end locations; clear words, and the words are not easy to fall off.對照電纜敷設清冊檢查Check as per the cable laying list固定fa
37、sten牢靠reliable扳動檢查check by pulling規格specification統一unified 觀察檢查visual check電纜固定Cable fasten固定fasten牢固fasten觀察檢查visual check夾具clamps型式model按設計規定as per design對照?qǐng)D紙檢查as per drawing 交流單芯電纜固定fastened by AC single core cable夾具無鐵件構成的閉合磁路non-iron clamps formed closed magnetic circuit觀察檢查visual check固定強度f(wàn)aste
38、ning strength 牢靠Firm and reliable 用手扳動檢查Check through pulling緊固件表面處理Surface treatment of the fastener 鍍鋅galvanized觀察檢查visual check敷設后檢查check after laying 電纜管口封閉Sealing of the cable pipe orifice按GB 50168-1992規定As per GB 50168-1992直埋電纜敷設Directly buried cable laying工序Process檢驗項目Inspection items性質Proper
39、ty 質量標準Quality standard檢驗方法與器具Inspection method and instrument 敷設前檢查Check before laying 電纜Cable 型號、電壓與規格Model, voltage and specification 符合設計Conform to the design對照?qǐng)D紙檢查Check as per the drawing長度Length 按設計,并聯運行的電力電纜長度應一致as per design, the length of the parallel operation power cable should be the sam
40、e.檢查電纜敷設記錄Check the cable laying record外觀檢查Appearance check無機械損傷和滲油No mechanical damage and oil infiltrate 觀察檢查visual check絕緣檢查Insulation check重要primary良好Fine 用10kv兆歐表檢查Check with the 10kv megger敷設地點檢查L(zhǎng)aying location check無積水,沉陷,在可能使電纜受到機械損傷,化學作用,地下電流、振動、熱影響,腐植物質、蟲鼠等危害的地段應有保護措施no water, concave; tak
41、e protection measures at the locations where the mechanical damage, chemical effect, underground current, vibration, thermal effect, humic substance may exist. 觀察檢查visual check電纜溝深度 depth of the cable trench0.7m用尺檢查check with tape 電纜敷設Cable laying敷設路徑laying route 按設計規定As per design對照?qǐng)D紙檢查check as per
42、 drawing 端頭密封end sealing油紙絕緣電力電纜Oil paper insulation power cable鉛封密實,無滲油Lead sealing, no oil infiltrate觀察檢查Visual check交聯聚乙烯電纜XLPE cable防潮端可靠,嚴密The anti-humidity end is reliable and tight.充油電纜Oil filled cable 按GB50168-1992規定As per GB 50168-1992電纜彎曲半徑Cable bending radius主要Primary 按GB50168-1992規定As pe
43、r GB 50168-1992用尺檢查Check with tape電纜與鐵路、公路、城市道路、廠區道路交叉敷設cable go across the railway, road, city road, plant road.電纜之間,電纜與管道、道路、建筑物之間平行和交叉的距離The parallel and crossing distances between the cable ad cable , cable and pipes, cable and road, cable and building主要primary交流單芯電纜排列方式AC single core cable arra
44、nge way按設計規定As per design觀察檢查visible check電纜回填Cable backfill 電纜外觀檢查Appearance check無機械損傷和滲油No mechanical damage and oil infiltrate 觀察檢查visible check電纜上下保護層(軟土或沙層)檢查the top and bottom protection layers(soft soil or sand layer) check按GB50168-1992規定As per GB 50168-1992對照規檢查Check as per specification方位標
45、志(樁)檢查Coordination sign(pile) check 裝設位置Installation location 主要Primary 電纜兩端、電纜直線段50m-100m處、電纜接頭與電纜改變方向的彎角處Both ends of cable, 50m-100m straight section of the cable, cable joint and bending of direction changing point 觀察檢查Visual check標志sign 字跡清晰,不易脫落clear writing, not easy to fall off 標樁規格防腐,統一anti
46、-corrosion, 標樁固定牢固Fasten 用手扳動檢查Check through pulling電纜終端制作安裝Cable terminal fabrication and installation工序Process 檢驗項目Inspection items性質Property 質量標準Quality standard 檢驗方法與器具Inspection method and instrument 制作前檢查check before fabrication電纜Cable 位置location 按設計規定As per design對照?qǐng)D紙檢查Check as per drawing 型號
47、、電壓與規格Model, voltage and specification 絕緣檢查insulation check主要Primary 良好Fine 檢查試驗記錄Check the test record電纜終端盒與配件cable terminal box and fittings 齊全,無損傷Complete, no damage對照技術文件檢查As per technical documents 制作工藝 fabrication process 按工藝規程規定As per process specification接地線Grounding wire接地線規格grounding wire
48、specification 按GB 50168-1992規定As per GB50168-1992對照規檢查As per specification 電纜穿過零序電流互感器接地線cable going through zero sequence CT grounding wire 接地線焊接grounding wire welding牢固 ,可靠Fasten, reliable 單芯電纜金屬層接地Single core cable metal layer grounding 一端接地one end grounding 觀察檢查Visual check 電纜芯線外觀檢查cable core wi
49、re appearance check 無損傷no damage芯線絕緣包扎長度Core wire insulation wrapping length 按工藝規程規定As per process specification 用尺檢查Check with tape 油紙電纜鉛封Lead sealing of the oil paper cable 位置location電纜終端盒金屬外殼與該處的電纜金屬護套cable terminal box metal shell and cable metal casing 觀察檢查Visual check 外觀檢查appearance check主要Pri
50、mary粘附密實,牢固,厚薄均勻,表面光滑,無夾渣,砂眼,縫隙affix tightly, fasten, equivalent thickness, smooth surface, no slag, crack環氧復合物配置和澆注Epoxy compoundconfiguration and pouring主要primary 按制造廠或工藝規程規定,攪拌均勻,無氣泡as per manufacture or process specification, stir equivalently, no bubble. 對照技術資料檢查As per technical documents 聚乙烯電纜
51、芯線外觀檢查Appearance check of polythene cable core wire 無碳痕,劃痕No carbon scar, no scratch 觀察檢查Visual check 預制電纜終端制作Prefabrication cable terminal box按制造廠規定As per manufacture specification 對照廠家資料檢查Inspect with manufacture documents熱縮電纜終端制作Heat shrinkable cable terminal fabrication 冷縮電纜終端制作Cold shrinkable c
52、able terminal fabrication 線鼻子Wire terminal 線鼻子規格wire terminal specification 與芯線相符 conform to the core觀察檢查visual check 銅鼻子鍍錫Copper terminal tin coating 表面光滑,干凈smooth surface and clean芯線連接Core wire connection 壓模規格Compression specification 與導線規格相符conform to the conductor specification 觀察檢查Visual check
53、壓入深度Compression depth 按工藝規程規定as per process specification 油紙電纜終端密封檢查Sealing check of oil paper cable terminal 主要Primary 無滲油no oil infiltrate 相色標志color sign symbol 正確correct 固定強度Fasten strength 牢固fasten 用手扳動檢查inspect through pulling by hand線鼻子與電氣裝置連接Connect the wire terminal with the electric device按GB50168-1992規定As per GB50168-
溫馨提示
- 1. 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
- 2. 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
- 3. 本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
- 4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
- 5. 人人文庫網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
- 6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
- 7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。
最新文檔
- 【正版授權】 IEC 60034-15:2025 EN-FR Rotating electrical machines - Part 15: Impulse voltage withstand levels of form-wound stator coils for rotating a.c. machines
- 2025至2030中國男式高腰皮鞋行業市場發展分析及競爭格局與投資前景報告
- 2025至2030中國狗肉行業深度研究及發展前景投資評估分析
- 教育心理學在課外活動中的應用分析
- 礦山教育培訓課件圖片
- 教育技術助力幼兒語言發展研究
- 商業培訓中的混合式游戲化教學模式研究
- 智能輔導系統在商業培訓中的創新實踐與思考
- 教育技術發展對教師角色的影響及倫理思考
- 抖音商戶數據分析師用戶行為建模制度
- 2025年廣東省中考英語試題卷(含答案解析)
- 2025年吉林省中考物理試卷真題及答案詳解(精校打印版)
- 標準的編寫講課件
- 新編阿拉伯語第三冊第二課課文及單詞
- 急性上消化道出血Blatchford評分
- DB12-T368-2008鹵蟲池塘養殖技術規范
- TSG11-2020 鍋爐安全技術規程
- 航圖zbyn太原武宿-機場細則
- 浙江省城市體檢工作技術導則(試行)
- 防火封堵施工方案(新版)
評論
0/150
提交評論