ZF AS Tronic系列-適用于各種商用車輛的自動變速器外文翻譯

1、The ZF AS Tronic Family Automotive Transmissions forAll Commercial Vehicle Classes1 Requirements for Commercial Vehicle Transmissions Customers demand high efficiency along with increasing vehicle comfort and safety. As an independent transmission manufacturer, ZF customer needs include the needs of

2、 drivers, forwarding companies, and vehicle manufacturers.Therefore, ZF considers the many requirements that a new transmission concept must fulfill when developing a transmission, Figure 1 . 圖1商用車輛的需求Fig. 1 Requirements for commercial vehiclesKeeping costs low is a considerable challenge, initially

3、 in terms of acquisition and later during operation. That is why fuel consumption is increasingly one of the decisive vehicle features that separate the competition. A modern transmission can make an important contribution here: On the one hand by improving efficiency and on the other hand in automa

4、tic transmissions by the optimal selection of the gear ratio dependent on the driving situation. Reducing the transmission, s weight also leads to reduced costs: Using less material reduces acquisition costs and enabling a higher payload reduces operating costs. On the one hand, decreased oil consum

5、ption contributes to environmental protection; additionally, it has an immediate influence on the costs, however, that accrue throughout the vehicle s service life.The demand for system comfort increasingly approaches the standard set by car technology, whereas in this case limits are set by mass ra

6、tios and cost constraints. Low noise emissions are a result of legal regulations on the one hand but also contribute to more comfortable driver workplaces when met. Furthermore, electronic systems increasingly support the driver and relieve him/her from routine tasks. This benefits safety in traffic

7、.2 Advances with Automatic TransmissionsAutomatic transmissions can satisfy many of the demands that customers make on commercial vehicles considerably better than manual transmissions. Despite the fact that automatic transmissions are generally more expensive, if one takes the complete installed ma

8、nual transmission system including the gearshift system into account, the difference in acquisition costs is no longer as great. Moreover, the goal of future developments is to further reduce the costs for automatic transmissions.Even today the higher acquisition costs are already paying for themsel

9、ves relatively quickly due to lower operating costs so that automatic transmissions are economically advantageous in the long run. The efficiency of the AS Tronic family of transmissions is comparable to a manual transition; however, as a rule, the shifting point selection is better due to the appli

10、cation of an automatic driving strategy, which positively affects fuel consumption. A long term study conducted by ZF and DEKRA found that the automatic shifting point selection represents the consumption performance of a very good, concentrated driver. Thus, averaging all drivers and driving situat

11、ions in a commercial fleet, consumption is reduced on the order of 3 percent since the engine operates reliably in the optimum speed range with regard to fuel consumption; a process that is controlled independently of the driver, s qualification.An additional advantage in terms of operating costs is

12、 reduced clutch wear. Reduced differential speeds during starting and shifting operations lengthen the service life of the clutch, which has al so been proven in long term tests. Many vehicle manufacturers take this into account and offer a significantly longer warranty cover on the clutch in AS Tro

13、nic transmissions.By automating the clutch, the clutch pedal is no longer needed, which clearly simplifies operation for the driver, particularly in stop and go traffic or when maneuvering. The automatic gear selection relieves the driver from shifting as well, whereby he/she can concentrate better

14、on road traffic. However, at the same time, the driver can engage manually at any time, for instance in driving situations where the drivers forward field of vision is in question. This takes place according to Shift by Wire via an electromechanical control switch so that only very little actuating

15、forces are applied when manually selecting gears. The rapid automatic shifting and the protection against operating error also contribute to the increase in driver comfort while at the same time protecting the transmission and driveline. In addition, the absence of a mechanical link between shift le

16、ver and transmission reduces cabin noise.Using an automatic transmission also has advantages for vehicle manufacturers. Like the clutch control, the complete shift linkage is no longer needed, which makes both left and right hand steering vehicles easy to manufacture. When designing the driver workp

17、lace, anything is possible in terms of operating the transmission.3 The ZF AS Tronic FamilyZF began developing automated manual transmissions for commercial vehicles early. The first product was a partially automated transmission with automatic pre selection, which was introduced into the market in

18、1984. Ten years later, an automated transmission followed with the introduction of the first AS Tronic; however, the driver still had to select gears. Its successor model was first equipped with an intelligent shift program, which has been in production since 1998. Thus, a fully automatic solution w

19、as offered in a heavy commercial vehicle for the first time.The chosen transmission concept for AS Tronic resulted in the most efficient solution possible for larger volumes. Extensive integration and removal of unnecessary components opened up potential cost savings. As a group drive, AS Tronic is

20、designed with an unsynchronized basic transmission and synchronized splitter and range change group, Figure 2. 圖2 ZF AS Tronic的3D剖示圖Fig. 2 ZF AS Tronic: 3D section cut In order to reduce the weight of the transmission, a design with two countershafts was chosen, which is optimal in this performance

21、class in terms of weight. Due to a modular design and a basic transmission with 3 or 4 speeds, l6 peed, 12 speed, and 10 speed variants could be represented.In the basic transmission, the synchronizations were replaced with shift dogs, because the synchronization can take place by controlling the in

22、ternal combustion engine in modern EDC engines. An additional transmission brake is then required for up shifts, which is located on one of the two counter shafts. A standard dry clutch is used. It is fully automatic so that a clutch pedal is no longer necessary. All automated components are pneumat

23、ically operated and are combined within modules that are integrated into the transmission housing. The coordinated operation of transmission, clutch, and engine takes place by electronic control, which is located in the shift module. The interfaces to the out side were minimized.AS Tronic was initia

24、lly limited to torques of 2, 300 Nm (12 speed) and 2, 600 Nm (16 speed). Afterward, variants were introduced in a two step development, which expand the torque ranges of 12 speed transmissions upwards. AS Tronic is offered in direct drive and overdrive designs and is generally available with an inte

25、grated secondary retarder “Intarder. Automatic transmissions have found increasing acceptance in heavy commercial vehicles in the past few years and enjoy enormous popularity among customers. However, the advantages of these transmissions are also demonstrated especially in light and medium duty com

26、mercial vehicles. Vehicles in these classes are primarily used in city and regional traffic. Relief from operating the transmission and the clutch is especially important in this case because the traffic environment requires the drivers full attention. Furthermore, this sector is marked by a high nu

27、mber of untrained drivers and frequent driver turnover. Therefore, reducing the drivers influence on fuel consumption and clutch wear is an unmistakable advantage, not to mention safeguarding against transmission and clutch damage caused by the driver.For these reasons ZF decided to expand the produ

28、ct portfolio for automatic transmissions systematically into the area of low torques, Figure 3. 圖3變速器型譜:ZF AS Tronic的轉矩范圍Fig. 3 Transmission portfolio： the ZF AS Tronic products with torque rangesStarting from the technical fundamental principle- two pedal solutions with automatic shifting and a cus

29、tomer benefit that is commensurate with the AS Tronic- smaller AS Tronic transmission will be developed as well. They receive additional coding to their genuine designation in order to mark their association to the respective vehicle applications. AS Tronic mid will be used for applications from 800

30、 Nm to 1, 600 Nm； AS Tronic lite will cover trucks in the lower torque range up to 1, 050 Nm with 6 speed transmissions.4 ZF AS Tronic midThe vehicle sector where the AS Tronic mid series will be used is very sensitive to price and highly differentiated in terms of application types. Thus, midrange

31、vehicles will service both distributor and long distance transport as well as construction sites. Therefore, one of the focal points of development lies in a cost effective design that will fulfill the many and diverse customer requirements easily and also cover the wide torque range.Consistent prod

32、uct planning led to the development of an uncompromising midrange transmission series designed for automation. It encompasses seven transmission types combined into one modular design. With 840 mm short and 900 mm long transmission variants, the modular design concept is primarily based on the varia

33、tion of the wheel widths in order to cover the torque ranges up to 1, 200 Nm and 1，600 Nm respectively. Both transmission lengths will be offered in direct and overdrive de signs. Compared to the AS Tronic, the AS Tronic mid transmissions are approx. 50 to 65 kg lighter. In order to optimize costs,

34、a consistent complexity management system was pursued. Approximately 40% of the components were taken from existing transmissions in production at ZF.In order to offer uniform automation technology for all commercial vehicles in the midrange and heavy duty sectors, the proven AS Tronic components su

35、ch as transmission/clutch actuators, electronics, and software were used. Due to the inter face equality this achieved, the vehicle manufacturer can offer both AS Tronic and AS Tronic mid series in almost identical vehicles with various drive line variants at minimal expense.In a preliminary concept

36、 study, various gear set concepts were considered. Eight gear set formulas were compared using eleven selected evaluation criteria in terms of function, costs, and deadline. In order to provide this complex decision matrix with the necessary transparency, a decision making software tool was used. Th

37、e choice was made for a 12 speed gear set (2x3x2), which is comparable to a conventional 9 speed gear set in terms of design space and weight and even has advantages compared to a 10 speed gear set, Figure 4.圖4 ZF AS Tronic mid變速器剖示圖 Fig. 4 ZF AS Tronic mid in complete viewIt consists of engaging an

38、d disengaging input constants ( splitter group), 3 speed main transmission, and an output end planetary drive stage (range change group). Synchronizations are used in the splitter and range change group; the main transmission shifting elements are designed as dogs. The gear steps has a slightly prog

39、ressive gear interval due to a small increase in the gear ratio. Thus, at a total gear spread of approx. 12. 8, the gear ratio of 23. 8 % from 11th to 12th speed is on par with a comparable 16 speed transmission. For the first time, the gear ratio of the reverse gear was designed 13. 1, i. e. slower

40、 than 1st gear on a range change group transmission by an offset engagement over the reverse idler gear. In close cooperation with the customers, high drivability was already emphasized in the specification phase. Upon completion of the rough design, the drivability release criteria of one customer

41、were already proven in simulations.A detailed cost analysis of the gear units in ZF transmissions led to the design of the planetary rear mounted range change group in the AS Tronic mid，in which the most cost effective solutions were adopted in each case. Thus, the design of the new gear unit is mar

42、ked by the synchronization of the AS Tronic and the gear set design of the Ecosplit Figure 5. 圖5 ZF AS Tronic mid:行星齒輪傳動Fig. 5 ZF AS Tronic mid： planetary drive detail The bearings of the swing fork in the range change group are realized between the two housing parts, which minimizes seal points to

43、the outside and possible corrosion weak points. The clutch actuating cylinder was turned in driving direction from the 6 o clock position for AS Tronic to the 8 oclock position for AS Tronic mid. This not only increases vehicle road clearance and brings the actuating cylinder out of the danger zone,

44、 it al so offers the flexibility to react to potential requirements pushed clutch release under compression.Different from the AS Tronic, the AS Tronic mid gear set will only be designed with one counter shaft. The solution was the best in a parameter study for the torque range considered, which tak

45、es into account both the modular design aspects as regards optimal gear set length variation as well as the legally permitted noise requirements. As a result, the developer faced an additional challenge. If the oil pump and transmission brake are each driven by one countershaft in the AS Tronic, the

46、n both components now must be combined in a joint, cost effective brake pump module.Maximizing transmission efficiency in order to reduce fuel consumption attracted much interest during development. By consistently changing splash lubrication to injection lubrication, quasi dry sump lubrication was

47、achieved so that diving losses do not occur. In order to optimize the lubrication system, oil flow calculations were conducted. The oil itself was handled like a structural/ design element. ZF has worked intensively for years with lubricant manufacturers in order to develop synthetic oils such as th

48、e ZF Ecofluid M, which is used in these transmissions. This oil has low viscosity and therefore contributes low internal losses; however, at the same time it offers sufficient lubricating film to guarantee the service life of gears, bearings, and synchronizations. An additional advantage of Ecofluid

49、 M is high stability, which makes clearly longer oil change intervals possible and greatly reduces oil consumption.Shift dogs in the main transmission and a com pact transmission design with small center distance also contribute to loss reduction. All these measures together increased the efficiency

50、 in the direct gear from 99. 2 to 99. 6% under comparable operating conditions. Active heat management enabled additional fuel savings. If the transmission runs at approx. 60 oil sump temperature on road, the oil viscosity can be further reduced by additionally heating to 80. In this case, AS Tronic

51、 mid is optionally available for the addition of a highly integrated heat exchanger. Short payback periods of approx, one year are ensured by cost effectively integrating the heat exchanger cartridge with the integrated bypass valve in the oil circulation on the intake side.ZF AS Tronic系列-適用于各種商用車輛的

52、自動變速器1商用車輛變速器的需求客戶的要求是在提高車輛舒適性和平安性的同 時也提高效率。作為一個獨立的變速器制造商，ZF 公司的客戶還包括駕駛?cè)藛T、運輸公司和車輛制造商。因此，ZF認為在開發變速器時就必須考慮到應 滿足各種需求，圖1)。圖1商用車輛的需求Fig. 1 Requirements for commercial vehicles繼續降低制造和使用本錢是一個很大的挑戰。這就是燃油經濟性為什么正成為車輛競爭的決定性因素之一的緣故。一個現代化的變速器具有以下奉獻：一方面通過優化速比改良效率、實現自動化、降低變速器重量以減少本錢、減少金屬材料用量降低制造本錢、提供更大的有效載 荷降低使用本錢

53、等。另一方面，減少燃油消耗還有助于環境保護，它直接影響到使用本錢，因而可提高 車輛的效勞壽命。對系統舒適性需求的增加已成為車輛技術的標準配置，盡管這受制于檔位數量和本錢限制。低噪聲一方面是由于法規要求，同時也提高了駕駛員工作環境的舒適程度。進一步而言，為駕駛員提供支持的電子系統減輕了他們的工作任務。這有益于交通平安。2自動變速器的優點自動變速器比手動變速器更能滿足客戶對商用車輛的需求。除了自動變速器本錢較高的事實外，但如果考慮到手動變速器及相應的換檔操縱系統的話，兩者本錢的差距并不太大。因此進一步開展的目標是降低自動變速器的本錢。在今天，較高的制造本錢由于更低的使用本錢而迅速補償，因此自動變速

54、器最終具有經濟性方面的優勢。將ZF AS Tronic系列變速器與手動變速器相比，由于采用了自動駕駛模式其換檔點的選擇更具優勢，這有助于燃油經濟性。一項由ZF和 DEKRA公司的長期研究發現換檔點的自動確定相當于一個具有高超技術駕駛員集中精力的駕駛。因而一個具有平均駕駛水平的車隊燃油消耗可降低 3%，因?yàn)榘l(fā)動機能可靠地工作在最正確速度區域，而整個過程與駕駛員的素質無關。另一個優點是可降低離合器的磨損。在起步和換檔過程中減少滑差可增加離合器的使用壽命，這己被長期試驗所證明。許多車輛制造商為配置AS Tronic變速器的車輛提供更長的離合器保修期限。采用自動離合器后，離合器踏板己不再需要，簡化了駕

55、駛員的工作，特別是在頻繁起步、停車工況下。檔位自動選擇解放了駕駛員的換檔動作，駕駛員的注意力可集中在道路交通上。同時,駕駛員仍可在任何時候切換為手動模式，例如當駕駛員視野出現問題時。這些都根據線控?fù)Q檔系統和機電一體化的控制開關完成，因此在手動換檔時僅需很小的操縱力。迅速地自動換檔和防止操縱失誤增加了駕駛舒適性，同時也保護了變速器和傳動系。另外變速器和換檔操縱桿之間無機械聯接可降低駕駛室的噪聲。使用自動變速器對車輛制造商也有好處。像離合器控制和換檔操縱裝置己不再需要，方便制造轉向盤左置和右置的車輛。在設計駕駛員工作區域時更能隨心所欲。3 ZF-AS Tronic 系列ZF早就開始開發適用于商用車

56、輛的機械自動變速器。第一個產品是帶自動預選檔位的半自動變速器，在1984年投入市場。十年后，推出的是AS Tronic的第一代產品，但是駕駛員仍需要選擇換檔。在1998年，其后續產品采用了智能化的換檔程序，而全自動化的產品那么首先用于重型商用車輛。圖2 ZF AS Tronic的3D剖示圖Fig. 2 ZF AS Tronic： 3D section cut選擇ZF AS Tronic變速器將具有更好大批量裝車的可能性。高度集成和省略不必要的元件使得在降低本錢方面仍具潛力。作為一組合式變速器，AS Tronic被設計成由不帶同步器的主變速器、前置同步分流的副變速器和擴展速比的后置副變速器組成，

57、圖2。為減輕主變速器的重量，采用了雙副軸結構。由于主變速器是3或4檔，因此可構成16、12和10檔的變速器。在主變速器，同步器被換檔檔塊所替換，因?yàn)橥竭^程可由現代化的EDC發動機完成。一個附加的變速器制動裝置用于升檔，它位于兩副軸之一上。采用標準的干式離合器。由于是全自動變速器故無需離合器踏板。所有的換檔元件由氣壓操縱并被以模塊形式集成在變速器殼體上。利用電控系統控制變速器、離合器及發動機，該裝置安裝在換檔模塊上。外部界面做成最小。AS Tronic的輸入轉矩為2300Nm(12速和 2600Nm(16速。副變速器具有2檔速比，它能擴大12速變速器的轉矩。AS Tronic提供直接傳動和超速

58、，通常集成一個第二緩速器“Intarder。在過去幾年里，自動變速器在商用車輛上的應用正在增加并贏得了消費者的巨大信任。然而，變速器的優點主要表達在輕型和中型商用車輛上。這些車輛主要行駛在城市和近郊交通繁忙的區域。這時減輕變速器和離合器的操作特別重要，因?yàn)榻煌ㄇ闆r需要駕駛員集中全部精力。另外，車輛是由大量非專業人員駕駛而且頻繁更換駕駛員。因此減少駕駛員對燃油消耗和離合器磨損的影響是一個顯著的優點，同時也減少了駕駛員對變速器和離合器的傷害。為此ZF決定系統地?cái)U(kuò)展自動變速器的產品型譜，如圖3。圖3變速器型譜:ZF AS Tronic的轉矩范圍Fig. 3 Transmission portfolio： the ZF AS Tronic pr