內容bmw g38文件確認rear

1、Title :LM-0030Site :LeadMouldProduct name: REAR COVER_HR_Rear3D file name : 2576494_1_REAR_COVER Date : 2015.06.10Confidential Design. Build. Ship. Service.LeadMouldProduct informationSegment :BMW G38Thickness :2.0 mmProject name :LM-0030 PM/PE Part name : REAR COVER_HR_Rear DFM by:Jiang lanPart No:

2、 2576494 Checked by:REVDate Update or added slidersRemark:155.45mm194.37mm37.87mmTool informationResin material : PP Resin supplier:N/AResin GradePP CX 02-82TonnageN/A Runner Sys: Drops openNo. of Hot Tip4Tool type :2 PLATEGate type :Direct gateAutomatic:YNo. of Gate .(each part)2Part weight (g) :72

3、.7x2 gCavity steelGS 1.2738HH 34-38HRCForecast volume (shot)79.50 x2 cm3Special tool :Incoe Core steelGS 1.2738HH 34-38HRC No. of Cavity:2Cosmetic part (Y/N):N/ASlider steelN/A Family with:Cosmetic finishingLifter steelN/ACustomer comment. (please give your approval and comments)OK or NGremarkApprov

4、al by:dateGate layoutCustomer comment. (please give your approval and comments)OK or NGremarkApproval by:date尖點熱咀直接進膠(產品增加凹槽6X0.5)Hop tip direct on part (add recess 6X0.5)參考樣件澆口殘留不能超出零件表面Part LayoutNeed to show part layout to avoid customer mis-understood our proposalTool topNotes: this layout is ba

5、se on estimation as a ref for tool design. Hot runner runner+ 4 Drops openOK澆口殘留不能超出零件表面shrinkageCustomer comment. (please give your approval and comments)OK or NGremarkApproval by:dateNotes: above shrinkage is estimated according to our understanding, pls correct it if there is any risk of getting

6、right dimensionShrinkage with orientationX1.016Y1.016Z1.016YX需要保證零件尺寸，新思路與立盛自行決定Parting line Customer comment. (please give your approval and comments)OK or NGremarkApproval by:dateParting line is defined as edge formed by Core / Cavity parting surfaces. P/ LINENotes: please advice any concern on pr

7、opose parting line.CorePLCavity insert/ LINE依據2D圖紙要求Parting line Customer comment. (please give your approval and comments)OK or NGremarkApproval by:dateParting line is defined as edge formed by Core / Cavity parting surfaces. Notes: please advice any concern on propose parting line.P/ LINECavityPLC

8、oreinsert/ LINE依據2D圖紙要求Parting line Customer comment. (please give your approval and comments)OK or NGremarkApproval by:dateParting line is defined as edge formed by Core / Cavity parting surfaces. Notes: please advice any concern on propose parting line.P/ LINECavityPLCoreinsert/ LINE依據2D圖紙要求Cavity

9、 insert Customer comment. (please give your approval and comments)OK or NGremarkApproval by:dateNotes: please advice any concern on witness line form by inserting.OK，需要保證產品質量Core insert /Pin Customer comment. (please give your approval and comments)OK or NGremarkApproval by:dateNotes: please advice

10、any concern on witness line form by inserting.OK，需要保證產品質量Draft angle informationProduct is checked in UG as per the direction of tooling release. This will help to evaluate draft angle and propose draft requirements.PL is decided on the basis of draft direction , if need, propose to reverse the draf

11、t angle or increase it for release the product easy. Mold opening direction開模方向IssueCustomer comment. (please give your approval and comments)OK or NGremarkApproval by:date前后模插穿以及插穿角度太小The shut-off is too smallPlease make core side draft.Color Propose Draft angleYellow1 (Remove plastic)黃色面1減膠參考樣件與歐洲

12、溝通更改可行性IssueCustomer comment. (please give your approval and comments)OK or NGremarkApproval by:datePlease make core side draft.Color Propose Draft angleYellow1 (Remove plastic)前后模插穿以及插穿角度太小The shut-off is too small黃色面1減膠參考樣件與歐洲溝通更改可行性IssueCustomer comment. (please give your approval and comments)OK

13、 or NGremarkApproval by:datePlease make cavity side draft.Color Propose Draft angleRed1 (Remove plastic)0.50mm建議更改分型線位置Propose to change P/L1度減膠參考樣件，維持特征線與歐洲溝通更改可行性IssueCustomer comment. (please give your approval and comments)OK or NGremarkApproval by:datePlease make cavity side draft.Color Propose

14、 Draft angleRed1 (Remove plastic)建議更改分型線位置Propose to change P/L1度減膠參考樣件，維持特征線與歐洲溝通更改可行性Thick plastic Customer comment. (please give your approval and comments)OK or NGremarkApproval by:dateNote: Thick ribs often cause sink and cosmetic problems on the opposite surface of the wall. Please refer the r

15、ib design guideline to modify as below:紅色位置可能有縮水The red area may have. sink mark與歐洲溝通縮痕可行性Ejector pin marksCustomer comment. (please give your approval and comments)OK or NGremarkApproval by:dateNote: only show the preliminary position and size, See layout for detail.Ejector pin 8Ejector pin 4Ejecto

16、r pin 10OK，要求頂桿印表面做平參考樣件制作凸臺，防止粘前模EngravingCustomer comment. (please give your approval and comments)OK or NGRemarkApproval by:datedate marks month/year:material indication：cavity number：Recycle stamp:article number：請?zhí)峁┰敿殨褡忠驪lease provide the engraving request參照2D圖紙Cosmetic requirementCustomer comment. (please give your approval and comment