鋰電池規格書

1、儲能型磷酸鐵鋰電池規格書STORAGE LiFePO4 BATTERY SPECIFICATIONS客戶名稱(Customer):產品型號(Type) :CF12V80Ah發行日期(Issuing Date):Prepared制定Checked審核Approved批準1. 適用范圍(Product Scope)本規格書描述了鋰離子二次電池的技術要求、測量方法、運輸、儲存及注意事項。This Specificationdescribes the requirements of the lithium ion rechargeablebattery supplied by2. 電池組特性(Batt

2、ery Group Specifications)Cell電芯Model規格型號IFP8081230-10AhCapacity 容量10 AhRated Voltage標稱電壓VInternal Resista nee內阻標準< 4 mQCombi natio n Sta ndard配組標準A. 容差 Capacity Differenee< 1%B. 內阻 Resistance()=1 2 mQC. 荷電保持能力 Current-maintaining Ability> 90%D. 電壓Combi natio n Method組合方式4串8并4S 8PPile In dex

3、成品參數Rated Capacity標稱容量Minimal Capacity最小容量(0.3C5A)Nomi nal Voltage額定電壓Max. Charge Voltage 最大充電電壓VDischarge cut-off voltage 放電截止電壓Charge Curre nt 充電電流5-10AWorki ng Curre nt工作電流10-20AOutput and In put輸出端與輸入端P+(red) / P-(black)Weight電池重量Dimension 外形尺寸(Lx W< H)168 x 260x 132mm不包含外露開關）Charge Method適用充

4、電Standard 標準5AX 16hrsQuick快速20AX 4hrs.Operat ingTemperature 適用溫度Charge充電0C45C; 32oF 113oFDischarge 放電-20C60C; -4°F 149oFMan ageme nt system管理系統Sin glecellover-chargecut-offvoltage單只過壓保護值Charge Worki ng voltage過壓釋放值Sin gle cell un der-discharge cut-off voltage單只欠壓保護值Discharge work ing voltage欠壓釋

5、放值Con diti ons of over-charge and un der-discharge voltage recovery 過、欠壓恢復條件With the high-po int voltage reach ing the work ingvoltage 極限電壓達到釋放值Over-charge cut-off curre nt過流保護值80AShort-circuit protection短路保護Own this ability具備此功能Con diti on for the recovery of over-curre nt and short-circuit protect

6、ion過流 短路保護恢復條件Cut the circuit to automatic recovery斷開負載自動恢復單只電芯曲線圖 feature curve for single cell3. 技術要求 (Technical Requirements)測試條件(除特別規定)Testi ng Con diti ons (unl ess otherwise specified) 溫 度 Temperature:1535°C相對濕度 Relative Humidity: 45%75%大氣壓 Atmospheric pressure: 86106Kpa充放電性能(Electrical C

7、haracteristics)NO項目(ITEM)測試方法(Testing Instruction)要求(Requirements)1Stan dard Charge標準充電Charg ing the cell in itially with con sta nt curre nt at0.5C and the n with con sta nt voltage at till charge curre nt decli nes to 0.05C先用0.5C恒流充電至，再恒壓充電直至充電電流w0.05C2Rated Capacity初始容量Measure discharge capacityw

8、ith discharge curre nt 1Cto cut-off with in 1 hour after sta ndard charge.標準充電方式充電后，以1C電流放電至的容量> 80Ah3Cycle Life循環壽命Measure the capacity after 2000 cycles of sta ndard charge and discharge at 1C curre nt to cut-off> 80 % of RatedCapacity標準充電方式充電后，1C放電至，如此循環2000次后電池 的剩余容量初始容量的80%4StorageCharact

9、eristics儲存性能Capacity after 30days storage at 25°C from sta ndardcharge標準充電方式充電后，25 C下儲存30天后的容量Rete nti on capacity> 90%剩余容量90%Capacity after 7days storage at 60C from sta ndardcharge標準充電方式充電后，60C下儲存7天后的容量Recovery capacity> 90%剩余容量90%環境性能(En viro nmen tai Characteristic)NO項目(ITEM)測試方法(Test

10、ing Instruction)要求(Requireme nts)1Temperature test ing 高低溫測試Measure capacity with constant discharge current 0.5C to cut-offat each temperature after standard chargeat 25 C, Percentage as an index of the capacity compared with 100% at 25 C25 C下標準充電方式充電后，在指定溫度下0.5C放電至的容量，并以25 C時放電容量為基準計算百分率70% at 0 C

11、100% at 25 C96% at 60 C2Con sta nt temperature /humidity 恒定濕熱性能Keep the battery at 40C and 90%RH for 96hrs將電池放入溫度為 40C，相對濕度為90%的條件下擱置96 小時Recovery capacity> 85%恢復容量85%機械性能(Mechanical characteristics)NO項目(ITEM)測試方法(Testing Instruction)要求(Requirements)1Vibrati on振動After standard charge, fixed the c

12、ell to vibrationtableand subjected to vibration cycling that the frequency is to be varied at the rate of 1Hz per minute betwee n 10Hz 55Hz, the excursion of the vibration is 1.6mm.The cell shall be vibrated for 30 minu tes per axis of XYZ axes.將標準充電后的電芯固定在振動臺上，沿X、Y、Z二個方向各振動30分鐘，振幅1.6 mm，振動頻率為10Hz55

13、Hz,每分 鐘變化為1Hz。The battery shall not rupture, smoke, catch fire, vent or leak and the voltage not be lower tha n 電池應無破裂、冒煙、 著火、泄漏或漏液，并 且電壓不低于2IFPacti ngTest ing碰撞After vibration , the battery will be IFPacted 1000 ± 10 times(60 ± 20 times per minute ) with the acceleration of 100 m/s and pu

14、lse lasting time 16ms.2將振動后的電池以峰值加速度為100 m/s的脈沖撞擊1000 ±10次(平均每分鐘60 ± 20次)，脈沖持續時間為16ms3Free fall自由跌落After IFPacting, the battery will be dropped free five times in three mutually perpe ndicular direct ions from the height of 1.0m onto a hard board with the thick ness of 20mm碰撞實驗結束后，將電池由高度為1

15、m的位置自由跌落到置于水泥地面上的20mm厚的硬木板上，從 X、Y、Z正負方向(六 個方向)每個方向自由跌落 1次安全性能(Safe Characteristic)NO項目(ITEM)測試方法(Testing Instruction)要求(Requireme nts)1Short Circuit短路After standard charge，the battery located in a fume hood is to be short-circuited by connecting the positive and negative terminals with an external l

16、oad of less than 50 mQ till the battery casetemperaturehasretur nedto n earambie nttemperature.將標準充電后的電池置于通風櫥中，短路其正負極(線 路總電阻不大于50m?),實驗過程中監視電池溫度變化， 當電池溫度卜降到接近初始室溫時，結束實驗The battery shall not rupture, smoke, catch fire, vent or leak.電池應無破裂、冒煙、著 火、泄漏或漏液2Abno rmalChanging Test過充After discharge to cut-of

17、fwith discharge current1C, the battery is to be subjected to a charg ingcurrent 3C.The specified charging current is to be obtained by connecting a resistor of the specified size and rating in series with the battery.The testtime is to be calculatedusing the formula:tc=2.5c/3(lc)將電池1C放電至后，調節電流 3C充電，

18、充電時間按以 下公式計算：tc = *電池額定容量/(3*制造商給定1C電流)3Over discharge test ing 過放Aftersta ndardcharge, the batterywillbeconn ected with exter nalwith a maximum resista neeload of Q for 24hrs un tilit is completelydischarged and the battery case temperature has retur ned to n ear ambie nt temperature.以標準方式充電后， 將電池正

19、負端以內阻小于歐姆的銅 導線連接24小時.，直至電池完全放電，溫度下降到環 境溫度4Pun cture穿刺After standard charge，the battery located in a fume hood is to be punctured with a nail (diameter > 1mm) until it is completely discharged and the battery case temperature has returnedto near ambienttemperature將標準充電后的電池置于通風櫥中，用直徑不小于1mm的針將電池從正面刺

20、穿，直至電池完全放電，溫度下降 到環境溫度4 電池組基本性能(Basic Characteristics of Battery)電池型號Battery Type4S8P IFP8081230外殼材質 Material of Case環氧樹脂Epikote額定電壓 Nominal VoltageV額定容量 Nominal Capacity80Ah(0.2C)內阻 Internal Resista nee<400 m?放電截止電壓 Discharge Cut-off Voltage最大充電電流 Max Charge Curre nt40A最大放電電流 Max Discharge Curre

21、nt160A最大充電電壓 Max Charge Voltage充電方法Charge methodCC/CV (con sta nt curre nt/con sta nt voltage)CC/CV (恒流恒壓)尺寸 Dimension長度 Thickness: <260mm寬度 Width: <168 mm高度 Height: <132mm重量Weight約：About:5 電池組保護功能要求(Battery Required Protection Functions)To in sure the safety, charger and the protect ioncir

22、cuit shall be satisfied the items below.As safety device, please use in comb in ati on with the temperature fuse. The sta ndard chargemethod is CC/CV (con sta nt curre nt/con sta nt voltage)為確保安全，充電器和保護電路應符合以下要求。同時請使用裝有熱熔保險絲的安全裝置。標準充電方法為CC/CV(恒流/恒壓)參數(product Specificati on)名稱(NAME)項目(ITEM)值(value)精

23、度(Precision )單位(unit)過充電壓(Over voltage)過充檢測電壓Ocv3900± 25mV過充恢復電壓Vcl3800± 50mV延遲 Delay Time1±S過放電壓(Under Voltage)過放檢測電壓Vcu2300± 80mV過放恢復放電Vcl2700± 100mV延遲 Delay Time100± 50mS充電電流(Charge Curre nt)充電電流OCw 5A過流延遲 OC Delay Time1000± 100mS工作電流(Curre nt)持續放電電流(Con ti nu o

24、us OutputDischarg ing Current )w 20A過放電流(Over Curre nt)過放保護電流OC80± 5A過流延遲 OC Delay Time10± 5mS靜態電流(Curre ntCon sumpti on)工作狀態Normal Modew 30uA休眠狀態Sleep ModewuA短路(Short Circuit)短路電流 SC600± 150A延遲 Delay Timew 1000uS恢復條件Recovery Con diti on斷開負載Manual regulati on6 保質期限及產品責任 WARRANTY PERIO

25、D & PRODUCT LIABILITYWarra nty period of this product is 24 mon ths from manu facturi ng code.保質期是從出廠日期(噴碼)開始起二十四個月.CHINENGs not responsible for the troubles caused by mishandling of the battery which is clearly against the instructions in this specification.池能公司對因沒有按本規格書規定操作而導致的意外不負責任When CHINE

26、NG finds any new facts which require modificati on of this docume nt, we will inform you aga in.一旦池能公司發現本規格書有新的修改細節，我們將再告知。7 包裝電池上的標示 INDICATIONS ON BATTERY PACKThe follow ing warnings should be in dicated on the battery packs. 以下警告應注明在包裝后的電池上Use a specified charger.使用規定的充電器Do not throw the battery

27、into fire, or heat.不要將電池投入火中或加熱Do not short-circuit the battery termi nals不要將電池兩端短路Do not disassemble the battery.不要將電池分解拆散8 電池使用時警告事項及注意事項WARNINGS AND CAUTIONS IN HANDLING THE Lithium-io n BATTER YTo prevent a possibility of the battery from leaking, heating or explosion please observe the followi

28、ng precauti ons:為防止電池可能發生泄漏，發熱、爆炸，請注意以下預防措施：WARNINGS!1. Do not immerse the battery in water or seawater, and keep the battery in a cool dry surro unding if it sta nds by.嚴禁將電池浸入海水或水中，保存不用時，應放置于陰涼干燥的環境中2. Do not use or leave the battery near a heat source as fire or heater禁止將電池在熱高溫源旁，如火、加熱器等使用和留置3. W

29、hen recharging, use the battery charger specifically for that purpose充電時請選用鋰離子電池專用充電器4. Do not reverse the positive (+) and n egative (-) term in als嚴禁顛倒正負極使用電池5. Do not connect the battery to an electrical outlet嚴禁將電池直接接入電源插座6. Do not discard the battery in fire or heat it禁止將電池丟于火或加熱器中7. Do not sho

30、rt-circuit the battery by directly connecting the positive (+) andn egative (-) termi nal with metal objects such as wire.禁止用金屬直接連接電池正負極短路8. Do not transport or store the battery together with metal objects such asn ecklaces, hairp ins etc.禁止將電池與金屬 , 如發夾、項鏈等一起運輸或貯存9. Do not strike or throw the batte

31、ry 禁止敲擊或拋擲、踩踏電池等10. Do not directly solder the battery and pierce the battery with a nail or other sharp object.禁止直接焊接電池和用釘子或其它利器刺穿電池CAUTIONS!1. Do not use or leave the battery at very high temperature (for example, at strong direct sunlight or in a vehicle in extremely hot weather). Otherwise, it c

32、an overheat or fire or its performance will be degenerated and its service life will be decreased. 禁止在高溫下(炙熱的陽光下或很熱的汽車中)使用或放置電池, 否則可能會引起電池過熱、起火或功能失效、壽命減短2. Do not use it in a location where static electricity is great, otherwise, the safety devices may be damaged, causing hidden trouble of safety.禁止

33、在強靜電和強磁場的地方使用 , 否則易破壞電池安全保護裝置 , 帶來不安全的隱患3. If the battery leaks, and the electrolyte get into the eyes. Do not rub eyes, instead, rinse the eyes with clean running water, and immediately seek medical attention. Otherwise, it may injure eyes or cause a loss of sight.如果電池發生泄露 , 電解液進入眼睛 , 請不要揉擦 , 應用清水沖洗眼睛 , 并立即送醫院治療 , 否則會傷 害眼睛4. If the battery gives off an odor, generates heat, becomes disc