3110發(fā)電機(jī)組控制器說(shuō)明英文V0-150807

1、GENSET CONTROLLER INSTALLATION INSTRUCTIONMode:3110CAKINVER. : V2.0-20150807Gensflt Control lorThe 3100 controller uses a 4.3 inch LCD display, with multiple languages interface. For automated operation of single genset, can monitor and protect genset. Through the button debugging operating paramete

2、rs, can also through the 232 communication interface to debug . You can operate 3110 controller after reading this instruction .Please contact our company technicians consulting when you have any questions .Measurement display data:Generation phase voltage: L1-N L2-N L3-NGeneration line voltage: L1-

3、2L2-3L3-1Generator current: A1 A2 A3Generator frequency: HzTotal power generation: KWEngine battery voltage: VEngine temperature: 0 C/ FEngine speed: RPMEngine oil pressure: PIS/BAREngine fuel quantity: %Engine running time:HAuxiliary sensor 1: C/ F ORPIS/BAR OR %Auxiliary sensor 2: C/ F ORPIS/BAR1.

4、 KEY FUNCTION DESCRIPTIONStop/Resetstop generator , reset to initial stateManual/Pagedown/DecreasPress this key will start genset.Shift cursor and decrease values.Auto/Page up/IncreaseSet/ConfirmPress this key will set the controller as Auto mode.Shift cursor and increase values.Into set menu after

5、pressing this key , confirm your select,Screen scroll;2.PARAMETER EDITINGThe controller parameter setting steps as follows:2.1 Press the buttonfor 3 seconds to enter the parameter settings, thenthe screen prompt input password as shown below:input password00002.2 Press the buttonstart to input passw

6、ord : “ 031&”2.3 Press the button to increase the data on the cursor , press thebutton to decrease the data on the cursor.Press the buttonto confirmthe data and move the cursor to next positon.2.4 If the password is right, you will see the display as shown below. Press the button to move up the curs

7、or and press the button to move down the cursor.Press the button 。can debug the parameters.0: Exit1: : System parameters2: Generator parameters3: Engine parameters2.5 Then you will see the display as shown below, Press the button O can debug the parameters. Press the button to increase the data on t

8、he cursor , press the button to decrease the data on the cursor.Press the button 。to confirm the data and move the cursor to next positon.1 : Current transformerSaved value :0100 /5ADebugging value : 0000 *2.6 After debug all parameters,press the button to exit.3 . PARAMETER RANGE AND DEFINATION3.1

9、system parametersNo.ParameterRangeDefaultDescription0Exit001Ratio of Current transformer5-9999100/5A0/invalid2Ratio of voltage transformer1.0-1001.0/1V3Rated voltage0-9999220VThe Phase voltage4Rated current0-9999100AThe total current5Rated power0-999922kW0/ invalid6Voltage input type1-310: NOT Used1

10、: 3P4W2: 1P2W。3: 2P3W7Start mode0-100: MANUAL , 1 : AUTO8語(yǔ)百 /Language0-100:中義，1: English9Communication address0-24703.2 generator parametersNo.ParameterRangeDefaultDescription0Exit001Gens under volt warning0-200%90%0/ invalid2Gens under volt stop0-200%80%0/ invalid3Gens over volt warning0-200%110%0/

11、 invalid4Gens over volt stop0-200%120%0/ invalid5Gens under freq warning0-100.0Hz48.0Hz0/ invalid6Gens under freq stop0-100.0Hz45.0Hz0/ invalid7Gens over freq warning0-100.0Hz55.0Hz0/ invalid8Gens over freq stop0-100.0Hz58.0Hz0/ invalid9Over power warning0-200%200%0/ invalid10Over power stop0-200%20

12、0%0/ invalid11Over power stop delay0-600s5s12Over current0-200%200%0/ invalid13Over current delay0-20s1s14Over current operation0-100: warning , 1 ： stop15Loading volt ratio0-100%95%16Loading volt freq0-100.0Hz48.0Hz17Loading delay0-9999s5s18Gens under volt warningdelay0-600s5s19Gens over volt warni

13、ng delay0-600s5s20Gens under freq warningdelay0-600s5s21Gens over freq warningdelay0-600s5s3.3 Engine parameterNo.ParameterRangeDefaultDescription0Exit001Rated speed0-9999RPM30002Speed sensor type0-110: no, 1： yes3Flywheel teeth0-300964Generator pole number1-415Temp. sensor type0-880/invalid6Oil pre

14、ssure type0-710/invalid7Start delay0-300s5s8Crank times1-1039Crank time1-30s5s10Crank interval time1-300s5s11Crank stop speed1-9999RPM30012Crank stop volt1-100%85%13Crank stop oil pressure0.1-150.0Bar1.0Bar14Crank stop oil pressure delay1-60s3s15Safty delay after crank0-600s5s16Idle time1-9999s30s17

15、Genset work safty delay0-600s10s18Cooling type0-110： rated , 1： idle19Cooling time0-600s30s20Stop fail delay0-60 秒10s21invalid0022Underspeed warning1-9999RPM27000/invalid23Underspeed stop1-9999RPM25000/ invalid24Overspeed warning1-9999RPM33000/ invalid25Overspeed stop1-9999RPM36000/ invalid26Under o

16、il pressure warning0.1-150.0Bar1.4Bar0/ invalid27Under oil pressure stop0.1-150.0Bar1.0Bar0/ invalid28Over temp. warning0-320 C100C0/ invalid29Over temp. stop0-320 C105C0/ invalid30Unerbattery volt1.0-40.0V8.0V0/ invalidwarning31Overbattery voltwarning1.0-40.0V30.0V0/ invalid32Under charge volt warn

17、ing1.0-40.0V12.0V0/ invalid33External crank allowed0-100: no, 1: yes34Under fuel warning0-100%10%0/ invalid35Underspeed stop delay0-600 秒5s36Overspeed stop delay0-600 秒3s37Under oil pressure stop delay0-600 秒3s38Over temp. stop delay0-600 秒5s39Fan 0N level0-320 C75C40Fan off level0-320 C65C3.4 Tempe

18、rature sensor typeNO.typeDescription0invalid1High temp. is close2Under temp. is off3VDO 120 C4VDO 150 C5Datcon6Murphy7Pt1008invalid3.5 Oil pressure sensor typeNO.typeDescription0invalid1High oil pressure is close2low oil pressure is off3VDO 5 Bar4VDO 10 Bar5Datcon 7 Bar6Murphy 7Bar7invalid3.6 Fuel l

19、evel sensor typeNO.typeDescription0invalid1High oil level is close2low oil level is off3invalid3.7 Input and output parametersNo.ParameterRangeDefaultDescription0Exit001Auxiliary input10-410/ invalid2Auxiliary input20-420/ invalid3Auxiliary input20-430/ invalid4Auxiliary input40-440/ invalid5Digital

20、 input 10-100 : close , 1 ： off6Digital input 20-100 : close , 1 ： off7Digital input 30-100 : close , 1 ： off8Digital input 40-100 : close , 1 ： off9Digital input 1 delay0-60s110Digital input 2 delay0-60s111Digital input 3 delay0-60s112Digital input 4 delay0-60s113Relay 10-1210/invalid14Relay 20-122

21、0/ invalid15Relay 30-1230/ invalid16Relay 40-1250/ invalid17Relay 50-1270/ invalid18Relay 60-1240/ invalid19Temp. low value0-320 C30 c20Temp. high value0-320 C85 c21Auxsensor1application0-330 : invalid1 : temp. C ,2 : oil pressure Bar ,3 : Fuel level %22Aux sensor 1 type0-1030/invalid23Aux sensor1 l

22、ow value0-9999024Aux sensor 1 low application0-310 : invalid,1 : varning ,2 : stop, 3 : control25Aux sensor 1 high level0-999900/invalid26Aux sensor 1 high application0-310123no, warning , stop, control27Auxsensor2application0-33012invalid temp. C, oil pressure Bar ,28Aux sensor 2 type0-1030/invalid

23、29Aux sensor 2 low value0-9999030Aux sensor 2 low application0-310123invalid, varning ,stop, control31Aux sensor 2 high level0-999900/invalid32Aux sensor 2 high application0-310123no, warning , stop, control33Oil pump open level0-100%20%34Oil pump close level0-100%70%3.8 Digital input typeNO.typeDes

24、cription0invalid1Low oil pressure switch2High temp switch3External stop4Remote start3.9 Relay output typeNO.typeDescription0invalid1Fuel pump control2start3Temp. sensor low level4idle5Load output switch6Temp. sensor high level7Fan controlTemp. sensor open at 75 C, temp. sensor close at 65 C8Aux sensor 1 low9Aux sensor 1 high10Aux sensor 2 low11Aux sensor 2 high12Fuel pump control13Fuel control(ON)14Stop Delay output15Warning output16Fault output17Idle(NO)3.10 Resistance table of temprature sensor12345678910resistance( Q)202537516313029091414001600Temp.( C