工程常用英語6頁

1、一. 結構類(Structure category):中文(Chinese)英文(English)中文(Chinese)英文(English)向上抽孔Up extrude(折彎上)加強肋Rib向下抽孔Down extrude墊腳Locator抽孔Extrusion穿孔(通孔)Through hole色拉孔Counter sink(Abbr.=Csink)底孔Pilot hole沉頭孔Counter bore(Abbr.=Cbore)定位孔Locating hole中心沖Center mark(NCT)異形孔Cutout噴點Center point(Laser)通風孔(散熱孔)Vent反折壓平H

2、eming避位孔Clearance向上抽引,抽凸Up draw forming(Or: Up emboss)段差Offset向下抽引,抽凸Down draw, forming(Or: Down emboss)卡槽Card guide凸點Bump(Dimple)抽芽孔Threaded extrusion hole (or: Extrude and tap)接地標志Ground symbol自攻牙Self-tap(Form thread or Swirl)半剪Half-shear攻牙Tap (thread)壓線Score工藝槽,狹縫Relief(Slot)印字Mark(Stamp)異形小折Fing

3、er抽橋Draw bridge標簽定位壓印Label locator mark掛鉤Hook全周壓毛邊All round burr半沖孔Spring slice焊點Welding point墨印(P/N)Ink stamp (P/N)箭頭符號Arrow symbol插孔Jack壓“L”印“L” mark凹坑?Drop pit(Or: dent)?壓毛邊?Coin / Deburr二. 五金類(Hardware category):中文(Chinese)英文(English)中文(Chinese)英文(English)圓棒Round Bar彈簧螺釘Captive screw(Spring-load

4、ed screw)螺母Nut銷釘Pin平頭螺母Nut flush鈹銅靜電導片Gasket, becu, EMI 自鎖螺母Nut self-clenching自攻螺絲Self tapping screw(Or: Self threading screw)螺柱Standoff靜電導片EMI Gasket螺栓Bolt泡棉靜電導片Gasket, foam, EMI螺絲Screw靜電導軌EMI rail平頭螺絲Flat head screw把手Ejector圓頭螺釘Button-head screw墊片Washer拉釘Rivet彈簧Spring平頭拉釘Flat head rivet標準件Standard

5、 parts圓頭拉釘Dome head rivet(Or: closed-end rivet)定位銷?Dowel pin?散熱器?Heat sink?三. 表面處理類(Finish category):中文(Chinese)英文(English)中文(Chinese)英文(English)表面處理Finish陽性化處理Anodize烤漆Coat(or paint)陽性氧化?Anodic oxidation?粉末烤漆Powder paint后鍍鋅處理Zinc post plate電鍍Plating鉻酸鹽處理Chromate絲印Silkscreen(Or. Pad print)鍍鎳Nickel p

6、lating拉絲Line grinding(Or: Brush)鈍化Passivate非電解鍍(化學鍍)Electroless plating不烤漆區Free of paint area外觀Cosmetic烤漆保護Painting masking鍍亮錫Bright Tin Plating鍍鋅Zinc plating噴沙Sand blasting四. 圖面注解類(Notes on drawing):中文(Chinese)英文(English)中文(Chinese)英文(English)數控程序和相同NC Program is same as 裝拉釘用For rivet 請用舊模具Please u

7、se old tooling裝螺絲用For screw每片料下4個單件4pcs/sheet(4pcs per sheet)抽鉚用For staking毛刺面向上Burr up工件對稱Symmetrical part未注明的Unmarked工件不對稱Unsymmetrical part折彎系數Folding factor折彎線共線Same bending line正(反)面印字Mark from Nearside (Farside)外徑Outside Diameter(Abbr. OD)代號Mark內徑Inside Diameter(Abbr. ID)剖視圖A-ASection A-A高度Hei

8、ght局部視圖ADetail AC向視圖View from C比例 4:1SCAL 4:1寬度Width數量Quantity (Qty.)Or. Amount長度Length備注Remark打磨平齊Grind Flush規格大小Specification(Abbr. Spec.)拉絲方向Brush direction打印字模Stamp letter細砂紙F(tuán)ine Grain機械鉚合至Mechanically stake to#220號以上砂紙Grain Number #220 or greater件數,片數Piece(Abbr. PCS)參考外觀規格Refer to cosmetic SPEC

9、幾處Places(Abbr. PLS)除非另外指明Unless otherwise specified注*號的尺寸Dimensions marked with “*”“*”代表“*” Denotes五. 制程類(Process category):中文(Chinese)英文(English)中文(Chinese)英文(English)折彎內圓角Internal Bend Radius點焊Spot welding印字Mark part NO.(Stamp part NO.)縫焊Seam welding按照制造說明安裝Install Per Manufactures instruction氬焊Ar

10、gon welding重點尺寸Critical Dimension抽鉚Staking隨制造日期變化Date changes according to actual Manufacture date拉鉚Riveting壓鉚五金件Press (install) hardware機加工Machining下料Blank (Blanking)銑Milling刻蝕Engrave(or: Etch)油壓機Hydraulic machine前加工Prep拉釘槍Rivet gun銼刀File銼毛刺To file burr鉆孔Drill螺絲起子Screw driverTox鉚合Toxing鎖緊(螺絲)Fasten

11、打磨Grind砂紙Sand paper折彎Bending毛刺面Burr side后定規Back gauge去毛刺Deburr折床Press brake模具,工具Tooling折彎線Bending line攻牙機Tapping machine鉚釘機Hardware insertion Machine點焊機Spot weld machine沖壓Stamping銳邊Sharp edge擴孔Enlarge hole去銳邊Remove sharp edges二次加工Second operation壓鉚Press-in治具Fixture/Gauge翻邊鉚Flare-in(Need Csink)制程控制Pr

12、ocess Control浮動鉚合Float-in(Need washer)組裝Assembly軸肘式鉚接Toggle lock沖頭Punch沖裁方向Punch direction用螺絲實配來檢查色拉孔Csink to be measured using a mating screw as a gauge螺絲頭須與裝配面平齊Head of screw must sit flush with mating surface置于Locate on 檢驗Inspection(Or: Check)六. 可制作性報告(DFM Report):中文(Chinese)英文(English)中文(Chinese

13、)英文(English)變形Deform(n. Deformation)確認Confirm(n. Confirmation)扭曲變形Tweak展開干涉Unfolding interference彈性變形Elastic deformation?組裝干涉Assembly interference可接收的Acceptable間隙配合 ?Clearance fit?可接收的規格Acceptance Spec.在自由狀態下In free state需開工藝槽Need cutting relief建義Suggestion折彎內尺寸太小Inside bending dimension is too shor

14、t解決辦法Solution抽形太高Forming is too high目前刀具規格Current tooling spec.Or available tooling 孔離折線太近The hole is too close to the bending line生銹Rust(Or. Corrosion)尺寸公差Dimensional tolerance間隙Gap平面度Flatness間隙過大Excessive gap垂直度Straightness斷裂(Be) broken, Or. (Be) cracked平行度Parallelism 錯位Mismatch傾斜的Slant偏離Deviate(n

15、. Deviation)太窄Too narrow太弱Too weak縮減Reduce刮傷Scratch對齊Align(n. Alignment)制造Fabricate(n. Fabrication)樣品Prototype功能Function量產Production修改Modify像素Feature忽略Forget (to do) Sth.(Ignore Sth)縮短, (使)變短Shorten延長, (使)變長Lengthen縮短2mmShorten by 2mm七. 其他類(Miscellaneous):中文(Chinese)英文(English)中文(Chinese)英文(English)

16、材料Material正面Nearside料厚Thickness(abbr. THK)反面Farside電鍍鋅板Electro-GalvanizedSteel (abbr. EG)向上(下)移動Move Upward (Downward)不銹鋼Stainless Steel(abbr. SUS or SS)見放大圖ASee detail A冷軋鋼板Cool roll steel(abbr. CRS)外(內)表面Exterior (Interior) surface熱浸鍍鋅鋼板Hot-dip zinc coated steel (or Galvanized Iron. Abbr. GI)貼紙Lab

17、eling熱軋鋼板SPHC鐵材零件Sheet metal parts馬口鐵SPTE(Or Tin)塑料零件Plastic parts鋁, 鋁合金Aluminum (alloy)卡尺Caliper熱鍍鋁鋼板Aludip包裝Packing黃銅Copper電子干擾Electrical Magnetic Interference (EMI)青銅Bronze材料清單Bill of material(Abbr. BOM)鈹銅Becu供貨商標識Vendor identification卷料Roll material工程變更通知Engineering Change Notice (abbr. ECN)圖面Drawing(abbr. DWG)工程改動要求Engineering Change Order (abbr. ECO)廢料Waste materials未標注的Undimensioned工程圖Procedure DWG料號Part Number(Abbr. P/N)棧板Pallet版次Revision(Abbr. Rev.)單位Unit供參考For your Information(Abbr. FYI)公制(米制)Metric大約位于指示位置Approximately whe