量具重復性和再現性數據表

1、,量具重復性和再現性數據表,NO:,版號:,A,修訂號:,1,表格編號, , ,量具名稱: caliper,硬度計,基準件名稱:,橡膠硬度塊,測量日期: ,15.06.18,量具編號:,IES-G-018,測量參數:,硬度,測量人員:,A B C ,量具量程: 0-99,參數規格:,80-90,評價人數,3,零,件,編,號,個數:,10,平均值,試驗次數,3,1,2,3,4,5,6,7,8,9,10,1.,A,1,85 ,84 ,84 ,83 ,84 ,84 ,84 ,83 ,85 ,84 ,84.0000,2.,2,84 ,84 ,84 ,83 ,84 ,85 ,84 ,83 ,85 ,84

2、 ,84.0000,3.,3,84 ,84 ,83 ,83 ,84 ,84 ,84 ,84 ,85 ,83 ,83.8000,4.,均值,84.333,84.000,83.667,83.000,84.000,84.333,84.000,83.333,85.000,83.667,83.93335., 極差,1.000,0.000,1.000,0.000,0.000,1.000,0.000,1.000,0.000,1.000,0.50006.,B,1,84 ,83 ,83 ,83 ,84 ,83 ,83 ,83 ,84 ,83 ,83.3000,7.,2,84 ,84 ,84 ,83 ,83 ,8

3、4 ,84 ,84 ,85 ,83 ,83.8000,8.,3,84 ,83 ,83 ,82 ,84 ,84 ,84 ,84 ,84 ,83 ,83.5000,9.,均值,84.000,83.333,83.333,82.667,83.667,83.667,83.667,83.667,84.333,83.000,83.533310., 極差,0.000,1.000,1.000,1.000,1.000,1.000,1.000,1.000,1.000,0.000,0.800011.,C,1,85 ,84 ,84 ,83 ,84 ,85 ,85 ,85 ,85 ,85 ,84.5000,12.,2,8

4、4 ,84 ,84 ,83 ,84 ,84 ,85 ,84 ,85 ,84 ,84.1000,13.,3,85 ,83 ,83 ,83 ,85 ,85 ,84 ,84 ,85 ,84 ,84.1000,14.,均值,84.667,83.667,83.667,83.000,84.333,84.667,84.667,84.333,85.000,84.333,84.233315., 極差,1.000,1.000,1.000,0.000,1.000,1.000,1.000,1.000,0.000,1.000,0.8000,零件均值,84.333,83.667,83.556,82.889,84.000,

5、84.222,84.111,83.778,84.778,83.667,83.9000,1.8889,極差均值,0.7,試驗次數,2,3,最大均值差,0.7000,D4,3.27,2.57,均值上限,84.6140,極差上限,1.7990,D3,0,0,均值下限,83.1860,極差下限,0,A2,1.88,1.02注:,圈出那些超出控制限的值。查明原因並糾正。同一評價人采用最初的儀器重復這些讀數或剔除這些值并由其余觀測值再次平均,并計算R和極限值.,均值圖,UCLx =,84.6140,84.6140,84.6140,84.6140,84.6140,84.6140,84.6140,84.6140,84.6140,84.6140,LCLx =,83.1860,83.1860,83.1860,83.1860,83.1860,83.1860,83.1860,83.1860,83.1860,83.1860,UCLR =,1.7990,1.7990,1.7990,1.7990,1.7990,1.7990,1.7990,1.7990,1.7990,