機械原理課程設計報告說明書

./機械原理課程設計說明書題目：碼頭吊車機構的設計及分析班級：機械0908姓名：學號：指導教師：成績：2011年9月目錄1.設計題目21.1機構簡圖21.2已知條件21.3設計要求32.運動方案及機構設計42.1連架桿O3C擺動范圍的確定42.2曲柄搖桿機構尺寸的設計73.運動分析計算及動態靜力分析83.1整體機構運動分析83.1.1實虛參對照表83.1.2程序83.1.3運行結果103.1.4線圖103.2整體機構動態靜力分析113.2.1實虛參對照表113.2.2程序123.2.3線圖143.2.4運行結果154.主要收獲18

碼頭吊車機構的設計及分析

一、題目說明圖示為某碼頭吊車機構簡圖。它是由曲柄搖桿機構與雙搖桿機構串聯成的。已知：lo1x=2.86m,lo1y=4m,lo4x=5.6m,lo4y=8.1m,l3=4m,l3'=28.525m,a3'=0.25°,l3′′=8.5m,a3′′=7°,l4=3.625m,l4′=8.35m,a4'=184°,l4′′=1m,a4′′=95°,l5=25.15m,l5'=2.5m,a5'=24°。圖中S3、S4、S5為構件3、4、5的質心,構件質量分別為：m3=3500kg,m4=3600kg,m5=5500kg,K點向左運動時載重Q為50kN,向右運動時載重為零,曲柄01A的轉速n二、內容要求與作法1.對雙搖桿機構O3CDO4進行運動分析,以O(shè)3C為主動件,取步長為1°計算K點位置,根據K點的近似水平運動要求,依據其縱坐標值決定O32.按O3C的擺動范圍設計曲柄搖桿機構O1ABO3,使搖桿O33.對整個機構進行運動分析,繪出K點水平方向的位移、速度和加速度線圖。4.只計構件3、4、5的質量,進行機構的動態靜力分析,繪制固定鉸鏈處反力矢端圖及平衡力矩Td線圖。上機前認真讀懂所用的子程序,自編主程序,初始位置取K點的右極限位置。主程序中打開一數據文件"DGRAPS",寫入需要顯示圖形的數據。三、課程設計說明書內容上機結束后,每位學生整理課程設計說明書一份,其內容應包括：1.機構簡圖和已知條件2.連架桿O3C3.桿組的拆分方法及所調用的桿組子程序中虛參與實參對照表。4.自編程序中主要標識符說明。5.主程序框圖。6.自編程序及計算結果清單。7.各種線圖：①K點坐標位置；②K點水平位移、速度和加速度線圖；③平衡力矩線圖；④固定鉸鏈處反力矢端圖。8.以一個位置為例,用圖解法對機構進行運動分析,與解析法計算結果比較誤差。9.主要收獲與建議。指導教師參考上述內容提出具體要求,學生按指導教師的要求書寫并裝訂成冊。一、題目說明：11點向左運動時載重Q為50kN,向右運動時載重為零,曲柄Ⅰ的轉速n3=1.06r/min已知尺寸：固定鉸鏈坐標：P4x=P4y=0,P1x=2.86m,P1y=4m,P7x=5.6m,P7y=8.1m,桿長：r45=28.525;r56=3.625;r67=25.15;r43=4.0;r511=8.35;r48=8.5;r59=1.0;r710=2.5;構件質量：m3=3500kg,m4=3600kg,m5=5500kg,99IVIV565611115VVIII7III78II2108II210332II1144機構簡圖拆分桿組二運動方案及機構設計：①以構件3為主動件：<1>調用bark函數求5點的運動參數形參n1n2n3kr1r2gamtwepvpap實參4503r450.00.0twepvpap<2>調用rrrk函數求6點的運動參數形參mn1n2n3k1k2r1r2twepvpap實參157645r56r67twepvpap<3>調用bark函數求4構件的位置角,角速度,角加速度和11點的位置,速度,加速度形參n1n2n3kr1r2gamtwepvpap實參501140.0r511gam1twepvpap<4>程序–對11點的運動軌跡分析#include"graphics.h"#include"subk.c"/*運動分析子程序*/#include"draw.c"/*繪圖子程序*/main<>{ staticdoublep[20][2],vp[20][2],ap[20][2],del; staticdoublet[10],w[10],e[10],pdraw[370],vpdraw[370],apdraw[370]; staticintic;/*定義靜態變量*/ doubler45,r56,r511,r67; doublegam1;doublepi,dr; doubler2,vr2,ar2; inti;/*定義局部變量*/ FILE*fp;/*定義文件指針變量*/ r45=28.525;r56=3.625;r511=8.35;r67=25.15; gam1=-184.0;del=1.0;/*賦值*/ t[4]=0.0;w[4]=0.0;e[4]=0.0; w[1]=0.0;e[1]=0.0; pi=4.0*atan<1.0>;dr=pi/180.0;/*求弧度*/ gam1=gam1*dr; p[4][1]=0.0; p[4][2]=0.0;w[3]=1.06*2*pi/60；p[7][1]=5.6;p[7][2]=8.1;/*賦值*/ printf<"\nThe KinematicParameters ofPoint11\n">; printf<"NoTHETA1S11V11A11\n">; printf<"degmm/sm/s/s\n">;/*在屏幕上寫表頭*/ if<<fp=fopen<"file1","w">>==NULL> { printf<"Can'topenthisfile.\n">; exit<0>; }fprintf<fp,"\nTheKinematicParametersofPoint11\n">;fprintf<fp,"NoTHETA1S11V11A11\n">;fprintf<fp," degmm/sm/s/s">;/*在文件filel中寫表頭*/ ic=<int><360.0/del>; for<i=0;i<=ic;i++>{ t[3]=<i>*del*dr; bark<4,5,0,3,r45,0.0,0.0,t,w,e,p,vp,ap>; rrrk<1,5,7,6,4,5,r56,r67,t,w,e,p,vp,ap>; bark<5,0,11,4,0.0,r511,gam1,t,w,e,p,vp,ap>; printf<"\n%2d%12.3f%12.3f%12.3f%12.3f",i+1,t[3]/dr, p[11][2],vp[11][1],ap[11][1]>; fprintf<fp,"\n%2d%12.3f%12.3f%12.3f%12.3f",i+1,t[3]/dr, p[11][2],vp[11][1],ap[11][1]>; pdraw[i]=p[11][2]; vpdraw[i]=vp[11][1]; apdraw[i]=ap[11][1]; if<<i%10>==0>{getch<>;}} fclose<fp>; getch<>; draw1<del,pdraw,vpdraw,apdraw,ic>; getch<>;}<5>數據--隨主動件3演變的11點運動參數〔從全部數據中篩選出的數據TheKinematicParametersofPoint11NoTHETA1S11V11A11 degmm/sm/s/s9392.00029.651-6.540-17.0879493.00020.156-14.10987.0449594.00020.127-8.76314.5309695.00020.176-7.2396.5749796.00020.244-6.4443.9149897.00020.315-5.9382.6609998.00020.385-5.5801.95510099.00020.451-5.3091.515101100.00020.511-5.0961.219102101.00020.565-4.9211.011103102.00020.612-4.7750.859104103.00020.653-4.6490.744105104.00020.686-4.5400.655106105.00020.713-4.4420.586107106.00020.733-4.3550.531108107.00020.747-4.2750.487109108.00020.755-4.2010.451110109.00020.756-4.1320.422111110.00020.752-4.0680.399112111.00020.742-4.0070.380113112.00020.727-3.9480.364114113.00020.708-3.8920.352115114.00020.684-3.8380.343116115.00020.656-3.7840.336117116.00020.625-3.7320.331118117.00020.591-3.6800.328119118.00020.555-3.6290.328120119.00020.517-3.5770.329121120.00020.478-3.5250.333122121.00020.439-3.4720.338123122.00020.401-3.4180.347124123.00020.364-3.3630.358125124.00020.331-3.3050.373126125.00020.302-3.2450.393127126.00020.280-3.1810.419128127.00020.266-3.1130.454129128.00020.263-3.0380.500130129.00020.275-2.9550.564131130.00020.306-2.8590.655132131.00020.361-2.7460.791133132.00020.450-2.6061.006134133.00020.586-2.4221.380135134.00020.791-2.1542.124所以O(shè)3C的擺動范圍為93°~134°②計算主動件和連桿桿長:程序:#include"math.h"#include"stdio.h"main<>{staticdoublel1,l2,l3,l4,max,min;staticdoublelx,ly;staticdoublethea0,thea1,thea2,pi,dr;/*弧度率*/pi=4.0*atan<1.0>;dr=pi/180.0;/*賦值*/l3=4.0;l4=sqrt<2.86*2.86+4*4>;lx=2.86;ly=4.0;thea0=atan2<ly,lx>+25.0*dr;thea1=93.0*dr-thea0;thea2=134.0*dr-thea0;/*計算兩桿長度*/min=sqrt<l3*l3+l4*l4-2*l3*l4*cos<thea1>>;max=sqrt<l3*l3+l4*l4-2*l3*l4*cos<thea2>>;l2=<max+min>/2;l1=<max-min>/2;printf<"\n\nl1=%12.3fl2=%12.3f",l1,l2>;}<2>數據:l1=1.388l三、運動分析計算及動態靜力分析1.以構件1為主動件對整體運動分析：<1>調用bark函數求2點的運動參數形參n1n2n3kr1r2gamtwepvpap實參1201r120.00.0twepvpap<2>調用rrrk函數求3點的運動參數形參mn1n2n3k1k2r1r2twepvpap實參142332r34r23twepvpap<3>調用bark函數求5點的運動參數形參n1n2n3kr1r2gamtwepvpap實參40530.0r45gam1twepvpap<4>調用rrrk函數求6點的運動參數形參mn1n2n3k1k2r1r2twepvpap實參157645r56r67twepvpap<5>調用bark函數求11點的運動參數形參n1n2n3kr1r2gamtwepvpap實參501140.0r511gam2twepvpap<6>程序--對11點位置,速度,加速度分析:#include"graphics.h"#include"subk.c"#include"draw.c"main<>{/*定義靜態數組*/staticdoublep[20][2],vp[20][2],ap[20][2];staticdoublet[10],w[10],e[10];staticdoublepdraw[370],vpdraw[370],apdraw[370];/*定義變量*/staticintic;doubledel,pi,dr;doubler45,r56,r67,r511,r34,r12,r23;doublegam1,gam2;inti;FILE*fp;/*按順序賦值*/del=10.0;pi=4.0*atan<1.0>;dr=pi/180.0;p[4][1]=0.0;p[4][2]=0.0;p[7][1]=5.6;p[7][2]=8.1;p[1][1]=2.86;p[1][2]=4.0;t[1]=0.0;w[1]=1.06*2*pi/60;r45=28.525;r56=3.625;r67=25.15;r511=8.35;r34=4.0;r12=1.388;r23=2.780;gam1=25.0*dr;gam2=176.0*dr;/*打印標題*/printf<"\nTheKinematicParametersofPoint11\n">;printf<"No.THETA1S11yS11xV11A11\n">;printf<"degmmm/sm/s/s\n">;if<<fp=fopen<"file_MO2.c","w">>==NULL>{printf<"Can'topenthisfile.\n">;exit<0>;}fprintf<fp,"\nTheKinematicParametersofPoint11\n">;fprintf<fp,"No.THETA1S11yS11xV11A11\n">;fprintf<fp,"degmmm/sm/s/s\n">;/*加入1,3點運動分析*/ic=<int><360.0/del>;for<i=0;i<=ic;i++>{t[1]=<i>*del*dr;bark<1,2,0,1,r12,0.0,0.0,t,w,e,p,vp,ap>;rrrk<1,4,2,3,3,2,r34,r23,t,w,e,p,vp,ap>;bark<4,0,5,3,0.0,r45,gam1,t,w,e,p,vp,ap>;rrrk<1,5,7,6,4,5,r56,r67,t,w,e,p,vp,ap>;bark<5,0,11,4,0.0,r511,gam2,t,w,e,p,vp,ap>;printf<"\n%2d%12.3f%12.3f%12.3f%12.3f%12.3f",i+1,t[1]/dr,p[11][2],p[11][1],vp[11][1],ap[11][1]>;fprintf<fp,"\n%2d%12.3f%12.3f%12.3f%12.3f%12.3f",i+1,t[1]/dr,p[11][2],p[11][1],vp[11][1],ap[11][1]>;pdraw[i]=p[11][1];vpdraw[i]=vp[11][1];apdraw[i]=ap[11][1];if<<i%4>==0>{getch<>;}}fclose<fp>;getch<>;draw1<del,pdraw,vpdraw,apdraw,ic>;}<7>線圖--11點水平位移,速度,加速度線圖<8>數據–隨主動件1演變的11點運動參數TheKinematicParametersofPoint11No.THETA1S11yS11xV11A11degmmm/sm/s/s10.00020.132-1.4080.471-0.155210.00020.156-0.9210.106-0.312320.00020.142-1.158-0.399-0.285430.00020.122-2.089-0.756-0.181540.00020.158-3.481-1.004-0.140650.00020.266-5.224-1.207-0.119760.00020.422-7.259-1.375-0.093870.00020.583-9.522-1.495-0.060980.00020.705-11.932-1.561-0.0231090.00020.756-14.400-1.5700.01111100.00020.725-16.842-1.5270.04212110.00020.625-19.179-1.4390.06913120.00020.486-21.347-1.3120.09214130.00020.351-23.288-1.1510.11315140.00020.270-24.951-0.9600.13116150.00020.286-26.292-0.7420.14517160.00020.419-27.276-0.5070.15218170.00020.627-27.887-0.2730.14319180.00020.781-28.147-0.0610.12920190.00020.735-28.0800.1510.14721200.00020.525-27.6440.4140.18722210.00020.328-26.7530.7220.19923220.00020.263-25.3781.0210.17624230.00020.333-23.5731.2610.12625240.00020.478-21.4591.4120.06426250.00020.625-19.1851.4660.00727260.00020.724-16.8911.441-0.03528270.00020.756-14.6801.365-0.05929280.00020.727-12.6121.264-0.06830290.00020.651-10.7101.157-0.06731300.00020.547-8.9711.056-0.06132310.00020.432-7.3840.965-0.05533320.00020.319-5.9320.884-0.04934330.00020.223-4.6010.810-0.04635340.00020.154-3.3850.735-0.05136350.00020.123-2.2980.640-0.07537360.00020.132-1.4080.471-0.1552.對整體機構動態靜力分析<1>調用bark函數求2點的運動參數形參n1n2n3kr1r2gamtwepvpap實參1201r120.00.0twepvpap<2>調用rrrk函數求3點的運動參數形參mn1n2n3k1k2r1r2twepvpap實參142332r34r23twepvpap<3>調用bark函數求5點的運動參數形參n1n2n3kr1r2gamtwepvpap實參40530.0r45gam1twepvpap<4>調用bark函數求8點的運動參數形參n1n2n3kr1r2gamtwepvpap實參40830.0r48gam9twepvpap<5>調用rrrk函數求6點的運動參數形參mn1n2n3k1k2r1r2twepvpap實參157645r56r67twepvpap<6>調用bark函數求9點的運動參數形參n1n2n3kr1r2gamtwepvpap實參50940.0.r59gam10twepvpap<7>調用bark函數求11點的運動參數形參n1n2n3kr1r2gamtwepvpap實參501140.0r511gam5twepvpap<8>調用bark函數求10點的運動參數形參n1n2n3kr1r2gamtwepvpap實參701050.0.r710gam11twepvpap<9>調用rrrf函數求各運動副中的反力形參n1n2n3ns1ns2nn1nn2nexfk1k1pvpaptwefr實參5769101101145pvpaptwefr<10>調用rrrf函數求各運動副中的反力形參n1n2n3ns1ns2nn1nn2nexfk1k1pvpaptwefr實參4238250032pvpaptwefr<11>調用barf函數求1點運動副反力及平衡力矩形參n1ns1nn1k1papefrtb實參1121papefr&tb<12>程序–加入對質心的運動分析,對固定鉸鏈的靜態動力分析,主動件反力偶#include"graphics.h"#include"subk.c"#include"draw.c"#include"subf.c"main<>{/*定義靜態數組*/staticdoublep[20][2],vp[20][2],ap[20][2];staticdoublet[10],w[10],e[10];staticdoubletbdraw[370],tb1draw[370],fr[20][2],fe[20][2];staticdoublesita4[370],fr4draw[370],sita7[370],fr7draw[370],sita1[370],fr1draw[370];/*定義變量*/staticintic;doubledel,pi,dr;doubler45,r56,r67,r34,r511,r12,r23,r48,r59,r710;doublegam1,gam5,gam9,gam10,gam11;doublefr4,fr7,fr1,bt4,bt7,bt1,we8,we9,we10,tb,tb4;inti;FILE*fp;/*按順序賦值*/del=10.0;pi=4.0*atan<1.0>;dr=pi/180.0;p[4][1]=0.0;p[4][2]=0.0;/*點位置*/p[7][1]=5.6;p[7][2]=8.1;p[1][1]=2.86;p[1][2]=4.0;t[1]=0.0;w[1]=1.06*2*pi/60.;/*主動件角速度*/sm[3]=3500.0;sm[4]=3600.0;sm[5]=5500.0;/*構件質量*/r45=28.525;r56=3.625;r67=25.15;r34=4.0;r511=8.35;r12=1.388;r23=2.780;r48=8.5;r59=1.0;r710=2.5;gam1=25.0*dr;gam5=176.*dr;gam9=18.0*dr;gam10=95.0*dr;gam11=-156.0*dr;/*打印標題*/printf<"\nTheKineto-staticAnalysisofEight-barLinkase\n">;printf<"No.THETA1Fr4Bt4Fr7Bt7Fr1Bt1TbTb4\n">;printf<"degNdegNdegNdegdegdeg\n">;if<<fp=fopen<"file_For.c","w">>==NULL>{printf<"Can'topenthisfile.\n">;exit<0>;}fprintf<fp,"\nTheKineto-staticAnalysisofEight-barLinkase\n">;fprintf<fp,"No.THETA1Fr4Bt4Fr7Bt7Fr1Bt1TbTb4\n">;fprintf<fp,"degNdegNdegNdegdegdeg\n">;/*主動件整周轉動*/ic=<int><360.0/del>;for<i=0;i<=ic;i++>{t[1]=<double><i>*del*dr;/*質心運動分析*/bark<1,2,0,1,r12,0.0,0.0,t,w,e,p,vp,ap>;rrrk<1,4,2,3,3,2,r34,r23,t,w,e,p,vp,ap>;bark<4,0,5,3,0.0,r45,gam1,t,w,e,p,vp,ap>;bark<4,0,8,3,0.0,r48,gam9,t,w,e,p,vp,ap>;rrrk<1,5,7,6,4,5,r56,r67,t,w,e,p,vp,ap>;bark<5,0,9,4,0.0,r59,gam10,t,w,e,p,vp,ap>;bark<5,0,11,4,0.0,r511,gam5,t,w,e,p,vp,ap>;bark<7,0,10,5,0.0,r710,gam11,t,w,e,p,vp,ap>;/*固定鉸鏈動態靜力分析*/rrrf<5,7,6,9,10,11,0,11,4,5,p,vp,ap,t,w,e,fr>;rrrf<4,2,3,8,2,5,0,0,3,2,p,vp,ap,t,w,e,fr>;barf<1,1,2,1,p,ap,e,fr,&tb>;//*固定鉸鏈力矢量*/fr4=sqrt<fr[4][1]*fr[4][1]+fr[4][2]*fr[4][2]>;bt4=atan2<fr[4][2],fr[4][1]>;fr7=sqrt<fr[7][1]*fr[7][1]+fr[7][2]*fr[7][2]>;bt7=atan2<fr[7][2],fr[7][1]>;fr1=sqrt<fr[1][1]*fr[1][1]+fr[1][2]*fr[1][2]>;bt1=atan2<fr[1][2],fr[1][1]>;/*虛位移簡易求平衡力偶*/extf<p,vp,ap,t,w,e,11,fe>;we8=-<ap[8][1]*vp[8][1]+<ap[8][2]+9.81>*vp[8][2]>*sm[3];we9=-<ap[9][1]*vp[9][1]+<ap[9][2]+9.81>*vp[9][2]>*sm[4]+fe[11][2]*vp[11][2];we10=-<ap[10][1]*vp[10][1]+<ap[10][2]+9.81>*vp[10][2]>*sm[5];tb4=-<we8+we9+we10>/w[1];printf<"\n%3d%11.3f%11.3f%11.3f%11.3f%11.3f%11.3f%11.3f%11.3f",i+1,fr4,bt4/dr,fr7,bt7/dr,fr1,bt1/dr,tb,tb4>;fprintf<fp,"\n%3d%11.3f%11.3f%11.3f%11.3f%11.3f%11.3f%11.3f%11.3f",i+1,fr4,bt4/dr,fr7,bt7/dr,fr1,bt1/dr,tb,tb4>;tbdraw[i]=tb;tb1draw[i]=tb4;/*對比曲線校驗*/sita4[i]=bt4;sita7[i]=bt7;sita1[i]=bt1;fr4draw[i]=fr4;fr7draw[i]=fr7;fr1draw[i]=fr1;/*固定鉸鏈反力失端圖*/if<<i%4>==0>{getch<>;}}fclose<fp>;getch<>;draw2<del,tbdraw,tb1draw,ic>;draw3<del,sita4,fr4draw,sita7,fr7draw,sita1,fr1draw,ic>;}/*函數返回工藝阻力fe[][]*/extf<p,vp,ap,t,w,e,nexf,fe>doublep[20][2],vp[20][2],ap[20][2],t[10],w[10],e[10],fe[20][2];intnexf;{fe[nexf][1]=0.0;if<vp[nexf][1]<0>{fe[nexf][2]=-50000.0;/*左移受力,右移不受*/}else{fe[nexf][2]=0.0;}}<13>線圖--主動件1的平衡力偶線圖;固定鉸鏈受力失端線圖<14>數據--4,7,1點固定鉸鏈力失;主動件平衡力偶TheKineto-staticAnalysisofEight-barLinkaseNo.THETA1Fr4Bt4Fr7Bt7Fr1Bt1TbTb4degNdegNdegNdegdegdeg1122516.20258.47229716.14265.76876942.228-174.117-10945.625-10945.6252147380.49455.85225130.92555.47299175.445-168.962-2493.449-2493.4493124045.79989.22651717.90585.0146842.897-164.070674.074674.0744190129.64672.61124046.56552.08676846.433-159.61217810.22417810.2245234177.03270.56621932.481-5.589109900.636-155.77341465.73941465.7396244476.84974.16429802.042-26.331105673.568-152.72356657.56756657.5677231619.14381.52636193.408-30.86875385.245-150.57653225.08953225.0898210065.61592.68241394.205-30.20030584.7